Término solicitado: SOLDADURA POR PUNTOS/(265,65,175)
8 Registro/s encontrado/s en CAT+NORMA
| Tipo de documento: | NORMA |
| Título: | ROBOTS AND ROBOTIC DEVICES — SAFETY REQUIREMENTS FOR INDUSTRIAL ROBOTS — PART 1: ROBOTS |
| Código de Doc.: | ISO 10218-1 |
| Autor Inst.: | International Organization for Standardization. ISO |
| Fecha: | 2011 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | ISO 10218-1:2011 specifies requirements and guidelines for the inherent safe design, protective measures and information for use of industrial robots. It describes basic hazards associated with robots and provides requirements to eliminate, or adequately reduce, the risks associated with these hazards.ISO 10218-1:2011 does not address the robot as a complete machine. Noise emission is generally not considered a significant hazard of the robot alone, and consequently noise is excluded from the scope of ISO 10218-1:2011.ISO 10218-1:2011 does not apply to non‑industrial robots, although the safety principles established in ISO 10218 can be utilized for these other robots. |
| ICS: | 25.040.30 Industrial robots. Manipulators |
| Idioma: | en |
| Edición: | second edition |
| Palabras Clave: | Aceros de bajo carbono; Recubrimientos; Soldadura por resistencia; Soldadura por puntos |
| Páginas: | 43p. |
| Ingreso de la Info.: | 2021-09-23 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | RESISTANCE WELDING -- PROCEDURE FOR SPOT WELDING OF UNCOATED AND COATED LOW CARBON STEELS |
| Código de Doc.: | ISO 14373 |
| Autor Inst.: | International Organization for Standardization. ISO |
| Fecha: | 2006 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | ISO 14373 specifies requirements for resistance spot welding in the fabrication of assemblies of uncoated and metallic coated low carbon steel, comprising two or three sheets of metal, where the maximum single sheet thickness of components to be welded is within the range 0,4 mm to 3 mm, for the following materials: uncoated steels; hot dip zinc or iron-zinc alloy (galvannealed) coated steel; electrolytic zinc, zinc-iron, or zinc-nickel coated steel; aluminium coated steel; zinc-aluminium coated steel |
| Campo de Aplic.: | ISO 14373 is applicable to the welding of sheets of the same or dissimilar thickness, where the thickness ratio is less than or equal to 3:1. It applies to the welding of three thicknesses, where the total thickness is less than or equal to 9 mm. Welding with the following types of equipment is within the scope of ISO 14373: pedestal welding equipment; gun welders; automatic welding equipment where the components are fed by robots or automatic feeding equipment; multi welders; robotic welders. The welding of organic coated or primer coated steels is not within the scope of ISO 14373 |
| Relac. con otras Normas: | ISO 669; ISO 5182; ISO 10447; ISO 14270; ISO 14329; ISO 15609-5; ISO 15614-12 |
| ICS: | 25.160.10 |
| Idioma: | en |
| Título en otro Idioma: | Soudage par résistance -- Mode opératoire pour le soudage par points des aciers a bas carbone revetus et non revetus |
| Edición: | first edition |
| Palabras Clave: | Aceros de bajo carbono; Recubrimientos; Soldadura por resistencia; Soldadura por puntos |
| Páginas: | 16p. |
| Ingreso de la Info.: | 2009-03-26 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | SPECIMEN DIMENSIONS AND PROCEDURE FOR MECHANIZED PEEL TESTING RESISTANCE SPOT, SEAM AND EMBOSSED PROJECTION WELDS |
| Código de Doc.: | ISO 14270 |
| Autor Inst.: | International Organization for Standardization. ISO |
| Fecha: | 2000 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | This International Standard specifies specimen dimensions and a testing procedure for mechanised peel testing of single spot, seam and projection welds, in overlapping sheets, in any metallic material of thickness 0,5 mm to 3 mm, where the welds have a maximum diameter of 7vt (where t is the sheet thickness in mm). With welds of diameter 5vt and 7vt it is possible to underestimate the value of peel force when using the recommended test specimen dimensions. The object of mechanized peel testing is to determine the peel force that the test specimen can sustain |
| Relac. con otras Normas: | ISO 7500-1 |
| ICS: | 25.160.40 |
| Idioma: | en |
| Título en otro Idioma: | Dimensions des éprouvettes et mode opératoire pour l'essai par déboutonnage mécanisé des soudures par résistance par points, à la molette et par bossages |
| Edición: | first edition |
| Palabras Clave: | Dimensiones; Probetas; Métodos de ensayo; Saltado; Mecanización; Soldadura por puntos; Soldadura por protuberancias; Soldadura por costura; Metales |
| Páginas: | 9p. |
| Ingreso de la Info.: | 2009-03-26 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | SPECIMEN DIMENSIONS AND PROCEDURE FOR SHEAR TESTING RESISTANCE SPOT, SEAM AND EMBOSSED PROJECTION WELDS |
| Código de Doc.: | ISO 14273 |
| Autor Inst.: | International Organization for Standardization. ISO |
| Fecha: | 2000 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | This International Standard specifies specimen dimensions and a testing procedure for shear testing of spot, seam and embossed projection welds, in overlapping sheets, in any metallic material of thickness 0,5 mm to 10 mm, where the welds have a maximum diameter of 7 vt (where t is the sheet thickness in mm). With welds of diameter 5vt and 7vt, the value of shear strength can be underestimated when using the recommended test specimen dimensions. The object of shear testing is to determine the shear force that the test specimen can sustain |
| Relac. con otras Normas: | ISO 7500-1 |
| ICS: | 25.160.40 |
| Idioma: | en |
| Título en otro Idioma: | Dimensions des éprouvettes et mode opératoire pour l'essai de cisaillement des soudures par résistance par points, a la molette et par bossages |
| Edición: | first edition |
| Palabras Clave: | Dimensiones; Probetas; Métodos de ensayo; Cizallamiento; Soldadura por puntos; Soldadura por protuberancias; Soldadura por costura |
| Páginas: | 8p. |
| Ingreso de la Info.: | 2009-03-25 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | SPECIFICATION FOR AUTOMOTIVE WELD QUALITY - RESISTANCE SPOT WELDING OF STEEL |
| Código de Doc.: | AWS D8.1M |
| Autor Inst.: | American Welding Society. AWS |
| Fecha: | 2007 |
| Estado: | |
| País de Origen: | United States |
| Objeto: | This specification express an industry consensus of quality characteristics and metrics pertinent to resistance spot welds on automotive steels. The evaluation methods and inpection criteria specified herein can be used to evaluate the effectiveness of particular welding equipment and procedures used to weld a particular base material combinations. This document contains both visual and measurable acceptance criteria for resistance spot welds in steels. The information contained herein may be used as an aid by designers, resistance welding equipment manufacturers, welded product producers, and others involved in the automotive industry and resistance spot welding of steels |
| Relac. con otras Normas: | AWS A 3.0; AWS D8.9M |
| Idioma: | en |
| Palabras Clave: | Metales; Soldadura por puntos; Aceros; Calidad; Resistencia de materiales; Especificaciones; Automóviles |
| Páginas: | 40p. |
| Ingreso de la Info.: | 2009-03-25 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | RESISTANCE WELDING -- WELDABILITY -- PART 2: ALTERNATIVE PROCEDURES FOR THE ASSESSMENT OF SHEET STEELS FOR SPOT WELDING |
| Código de Doc.: | ISO 18278-2 |
| Autor Inst.: | International Organization for Standardization. ISO |
| Fecha: | 2004 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | ISO 18278-2:2004 specifies a laboratory test procedure for the determination of the acceptable welding current range and the assessment of electrode life using a multi-spot test with specific conditions |
| Campo de Aplic.: | ISO 18278-2:2004 is applicable for the assessment of the weldability of uncoated and coated sheet steels of thicknesses up to 3 mm. The test procedure specified in this International Standard and the results obtained, apply only for the introduction of a new type or batch of material |
| Relac. con otras Normas: | EN 22768-1, EN 28768-2, EN 25821, EN ISO 51833-1, EN ISO 6520-2, EN ISO 8166, EN ISO 14272, EN ISO 14273, EN ISO 14327, EN ISO 14329, EN ISO 15609-5, EN ISO 15614-12, EN ISO 18278-2, ISO 69, ISO 5182, iSO 14447, ISO/DIS 14373, ISO/DIS 17657-1, ISO/DIS 17657-2, ISO/DIS 17657-4, ISO/DIS 17657-5 |
| ICS: | 25.160.40 |
| Idioma: | en |
| Título en otro Idioma: | Soudage par résistance -- Soudabilité -- Partie 2: Méthodes alternatives d'évaluation des tôles d'acier pour le soudage par points |
| Edición: | first edition |
| Palabras Clave: | Soldadura; Soldadura por reistencia; Métodos de ensayo; Soldadura por puntos; Aceros; Chapas; Evaluación |
| Páginas: | 20p. |
| Ingreso de la Info.: | 2009-03-11 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | RESISTANCE WELDING -- WELDABILITY -- PART 1: ASSESSMENT OF WELDABILITY FOR RESISTANCE SPOT, SEAM AND PROJECTION WELDING OF METALLIC MATERIALS |
| Código de Doc.: | ISO 18278-1 |
| Autor Inst.: | International Organization for Standardization. ISO |
| Fecha: | 2004 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | ISO 18278-1:2004 recommends procedures for determining the generic weldability for resistance spot, seam and projection welding of metallic materials |
| Campo de Aplic.: | This procedure is applicable for the assessment of the weldability of uncoated/coated steels, stainless steels and non-ferrous alloys such as aluminium, titanium, magnesium and nickel and their alloys of single thickness lower than or equal to 5 mm. the ability to make the weld in the first place; the ability to continue making welds; the ability of the weld to withstand the imposed service stresses. compare the weldability of different metallic materials; compare the welding response of particular welding equipment and allow comparisons between different equipment and determine the influence of the static/dynamic properties of different welding equipment; determine the weldability of a material when any welding configuration is changed e.g. electrode material and/or shape, water cooling requirements etc.; investigate the effect of welding parameters such as welding current, weld time, electrode force or complex welding schedules including pulse welding, current stepping etc. on weldability |
| Relac. con otras Normas: | EN ISO 8166, EN ISO 14270, EN ISO 14271, EN ISO 14272, EN ISO 14273, EN ISO 14327, EN ISO 14329, EN ISO 15609-5, EN ISO 15614-12, EN ISO 18278-2, ISO 69, ISO/DIS 14373, ISO/DIS 16432, ISO/DIS 16433 |
| ICS: | 25.160.01 |
| Idioma: | en |
| Título en otro Idioma: | Soudage par résistance -- Soudabilité -- Partie 1: Évaluation de la soudabilité pour le soudage par résistance par points, à la molette et par bossages des matériaux métalliques |
| Edición: | first edition |
| Palabras Clave: | Soldadura; Soldadura por reistencia; Métodos de ensayo; Soldadura por puntos; Soldadura por cordón; Soldadura por protuberancias; Materiales metálicos; Evaluación |
| Páginas: | 7p. |
| Ingreso de la Info.: | 2009-03-11 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | SPECIMEN DIMENSIONS AND PROCEDURE FOR CROSS TENSION TESTING RESISTANCE SPOT AND EMBOSSED PROJECTION WELDS |
| Código de Doc.: | ISO 14272 |
| Autor Inst.: | International Organization for Standardization. ISO |
| Fecha: | 2000 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | This International Standard specifies specimen dimensions and a testing procedure for the cross tension testing of spot and projection welds in overlapping sheets in any metallic material of thickness 0,5 mm to 3 mm, where the welds have a maximum diameter of 7â. t (where t is the sheet thickness in mm).The object of cross tension testing is to determine the tensile force that the test specimen can sustains |
| Relac. con otras Normas: | ISO 7500-1 |
| ICS: | 25.160.40 |
| Idioma: | en |
| Título en otro Idioma: | Dimensions des éprouvettes et mode opératoire pour l'essai de traction sur éprouvettes en croix des soudures par résistance par points et par bossages |
| Edición: | first edition |
| Palabras Clave: | Dimensiones; Probetas; Métodos de ensayo; Tracción; Soldadura por puntos; Soldadura por protuberancias |
| Páginas: | 8p. |
| Ingreso de la Info.: | 2009-03-11 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
Fin
[Página de Inicio] [Nueva Búsqueda][Página Anterior]