Término solicitado: HILOS DE ROSCA/(265,65,175)
15 Registro/s encontrado/s en CAT+NORMA
| Tipo de documento: | NORMA |
| Título: | SCREW GAUGE LIMITS AND TOLERANCES. SPECIFICATION FOR GAUGES FOR SCREW THREADS OF WHITWORTH AND B.A. FORMS |
| Código de Doc.: | BS 919-2 |
| Autor Inst.: | British Standards. BSI |
| Fecha: | 2007 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| País de Origen: | United Kingdom |
| Objeto: | Gauges for general and reference use, and setting plugs for screw ring and thread caliper gauges. Tolerances apply to gauges for screw threads of Whitworth and BA forms. General requirements, tables of tolerances; appendices on conventional illustration of tolerance zones, effective diameter equivalent of pitch and angle errors, thread form of not go effective diameter gauges and setting plugs, examples of the use of tolerance tables |
| ICS: | 21.040.20 |
| Otros Códigos: | ISBN 978 0 580 68657 3 |
| Idioma: | en |
| Título en otro Idioma: | Limites et tolerances des calibres de vis. Specification. Calibres pour filetages de formes Whitworth et BA; Grenzwerte und Toleranzen von Gewindelehren. Spezifikation. Lehren fuer Schraubgewinde nach Whitworth und BA |
| Edición: | fourth edition |
| Notas: | Incorporating Corrigendum, 1 (september 2009) |
| Palabras Clave: | Roscas; Mediciones; Instrumentos de medición; Tornillos; Diámetro; Calibración; Medidores; Tolerancia; Hilos de rosca; Marcado; Dureza; Dimensiones |
| Páginas: | 42p. |
| Ingreso de la Info.: | 2012-09-10 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | PARALLEL SCREW THREADS OF WHITWORTH FORM. REQUIREMENTS |
| Código de Doc.: | BS 84 |
| Autor Inst.: | British Standards. BSI |
| Fecha: | 2007 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| País de Origen: | United Kingdom |
| Objeto: | This British Standard specifies limits of sizes, and tolerances, for single start parallel screw threads of Whitworth form, for general engineering use. While Whitworth threads have remained unchanged since the last revision of BS 84 in 1956, the present revision of the Standard has been undertaken on the basis that Whitworth threads will undoubtedly continue to be used for many years, especially on replacements or spare parts. This standard specifies the following thread series: a) a coarse thread series, the British Standard Whitworth (B.S.W.) series, with nominal diameters in the range 1/8 in to 6 in; b) a fine thread series, the British Standard fine (B.S.F.) series, with nominal diameters in the range 3/16 in to 4 1/4 in; c) a supplementary selected thread (WHIT. S.) series with nominal diameters from 1/4 in to 7 in; d) a truncated Whitworth form series. BS 84:2007 contains:Normative reference; Terms, definitions and symbols; Profile of Whitworth screw thread; Tolerance classes of external and internal thread; Limits of sizes, and tolerances, for uncoated B.S.W. and B.S.F. threads; Limits of sizes, and tolerances, for B.S.W. and B.S.F. coated threads; Stainless steel external threads; Selected thread series; Designation of screw threads of Whitworth form; Gauges |
| ICS: | 21.040.20 |
| Otros Códigos: | ISBN 9780580579233 |
| Idioma: | en |
| Edición: | fourth edition |
| Notas: | BS 84:2007 replaces BS 84:1956, which is withdrawn |
| Palabras Clave: | Roscas; Hilos de rosca; Hilos paralelos; Diámetros; Pernos; Dimensiones; Recubrimientos metálicos; Tolerancia |
| Páginas: | 66p. |
| Ingreso de la Info.: | 2012-09-10 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS -- PART 2: VERIFICATION BY MEANS OF LIMIT GAUGES |
| Código de Doc.: | ISO 228-2 |
| Autor Inst.: | International Organization for Standardization. ISO |
| Fecha: | 1987 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | Specifies the verification of cylindrical threads, the dimensions and tolerances of which are given in ISO 228-1. Since this 55o profile has different elements to be verified, it is necessary to provide for several GO and several NOT GO gouges. This second edition cancals and replaces the first edition (1980) |
| ICS: | 21.040.30 |
| Idioma: | en |
| Título en otro Idioma: | Filetages de tuyauterie pour reccordement sans étanchéité dans le filet - Partie 2: Verification par calibres à limites |
| Edición: | second edition |
| Palabras Clave: | Roscas; Tuberías; Hilos de rosca; Válvulas; Presión; Verificación; Calibración; Mediciones; Indicadores; Límites |
| Páginas: | 13p. |
| Ingreso de la Info.: | 2012-08-28 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS -- PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION |
| Código de Doc.: | ISO 228-1 |
| Autor Inst.: | International Organization for Standardization. ISO |
| Fecha: | 2000 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | This part of ISO 228 specifies the requirements for thread form, dimensions, tolerances and designation for fastening pipe threads, thread sizes 1/16 to 6 inclusive. Both internal and external threads are parallel threads, intended for the mechanical assembly of the component parts of fittings, cocks and valves, accessories, etc |
| Campo de Aplic.: | These threads are not suitable as jointing threads where a pressure-tight joint is made on the thread. If assemblies with such threads must be made pressure-tight, this should be effected by compressing two tightening surfaces outside the threads, and by interposing an appropriate seal |
| ICS: | 21.040.30 |
| Idioma: | en |
| Título en otro Idioma: | Filetages de tuyauterie pour reccordement sans étanchéité dans le filet - Partie 1: Dimensions, tolérances et désignation |
| Edición: | fourth edition |
| Palabras Clave: | Roscas; Tuberías; Hilos de rosca; Válvulas; Presión; Dimensiones; Tolerancia; Mediciones |
| Páginas: | 8p. |
| Ingreso de la Info.: | 2012-08-28 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | TECHNICAL CORRIGENDUM 1 - ISO GENERAL PURPOSE METRIC SCREW THREADS. TOLERANCES. PRINCIPLES AND BASIC DATA |
| Código de Doc.: | ISO 965-1:1998/Cor 1:2009 |
| Autor Inst.: | International Organization for Standardization. ISO |
| Fecha: | 2009 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| ICS: | 21.040.10 Metric screw threads |
| Idioma: | en |
| Título en otro Idioma: | Rectificatif Technique 1 - Filetages métriques ISO pour usages généraux. Tolérances. Principes et données fondamentales; Metrisches ISO-Gewinde allgemeiner Anwendung. Prinzipien und Grundlagen |
| Edición: | third edition |
| Palabras Clave: | Roscas; Roscas métricas; Tornillos; Hilos de rosca; Tolerancia; Dimensiones; Requisitos |
| Páginas: | 2p. |
| Ingreso de la Info.: | 2012-08-28 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | ISO GENERAL PURPOSE METRIC SCREW THREADS. TOLERANCES. PRINCIPLES AND BASIC DATA |
| Código de Doc.: | ISO 965-1 |
| Autor Inst.: | International Organization for Standardization. ISO |
| Fecha: | 1998 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | This part of ISO 965 specifies the basic profile for ISO general purpose metric screw threads (M) conforming to ISO 261. The tolerance system refers to the basic profile in accordance with ISO 68-1 |
| ICS: | 21.040.10 Metric screw threads |
| Idioma: | en |
| Título en otro Idioma: | Filetages métriques ISO pour usages généraux. Tolérances. Principes et données fondamentales; Metrisches ISO-Gewinde allgemeiner Anwendung. Prinzipien und Grundlagen |
| Edición: | third edition |
| Palabras Clave: | Roscas; Roscas métricas; Tornillos; Hilos de rosca; Tolerancia; Dimensiones; Requisitos |
| Páginas: | 21p. |
| Ingreso de la Info.: | 2012-08-28 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | SCREW THREAD GAGING SYSTEMS FOR ACCEPTABILITY: INCH AND METRIC SCREW THREADS (UN, UNR, UNJ, M, AND MJ) |
| Código de Doc.: | ANSI/ASME B1.3-2007 |
| Autor Inst.: | The American Society of Mechanical Engineers. ASME |
| Fecha: | 2007 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| País de Origen: | US |
| Objeto: | This Standard presents screw thread gaging systems suitable for determining the acceptability of UN, UNR, UNJ, M, and MJ screw threads on externally and internally threaded products. It establishes the criteria for screw thread acceptance when a gaging system is used. A screw thread gaging system comprises a list of screw thread characteristics that must be inspected/ evaluated to establish the acceptability of the screw threads on a threaded product and the gage(s) which shall be used when inspecting/evaluating those characteristics. Federal Government Use. This Standard is approved by the Department of Defense and federal agencies, and is incorporated into FED-STD-H28/20, Screw Thread Standards for Federal Services, Section 20. The use of this Standard by the federal government is subject to all the requirements and limitations of FED-STD-H28/20.This product referenced by:ANSI/ASME B18.2.5M-2009 - Metric 12-Point Flange Screws API RP 621 - Reconditioning of Metallic Gate, Globe, and Check Valves, Third Edition ANSI/ASME B18.6.9-2010 - Wing Nuts (Inch Series) ANSI/ASME B18.31.4M-2009 - Threaded Rod (Metric Series) ANSI/ASME B18.18-2011 - Quality Assurance for Fasteners ANSI/API Spec 6A - Specification for Wellhead and Christmas Tree Equipment, Twentieth Edition (ISO 10423:2009 Modification), Includes Errata (Jan. 2011) This product replaces:ANSI/ASME B1.3M-1992 - Screw Thread Gaging Systems for Dimensional Acceptability - Inch and Metric Screw Threads (UN, UNR, UNJ, M, and MJ) - Includes July 1994 Errata Browse Product Family: ANSI/ASME B1.3-2007 - 12-Oct-2007. ANSI/ASME B1.3M-1992 - 01-Jan-1992. People Who Bought This Also Bought: ANSI/ASME B1.2-1983 (R2007) - Gages and Gaging for Unified Inch Screw Threads ANSI/ASME B1.16M-1984 (R2006) - Gages and Gaging for Metric M Screw Threads ANSI/ASME B1.1-2003 (R2008) - Unified Inch Screw Threads, UN and UNR Thread Form ANSI/ASME B31.5-2006 - Refrigeration Piping and Heat Transfer Components ANSI/ASME B1.7-2006 - Screw Threads: Nomenclature, Definitions, and Letter Symbols ANSI/AWS A2.4:2007 - Standard Symbols for Welding, Brazing, Nondestructive Examination DIN Handbook 55 - Fasteners 3 - Technical Delivery Standards for Bolts, Screws, Nuts and Washers - Paperback DIN Handbook 10 - Fasteners 1 - Dimensional Standards for Bolts, Screws and Studs ANSI/ASME B18.18.1-2007 - Inspection and Quality Assurance for General Purpose Fasteners ANSI/ASME B18.7-2007 - General Purpose Semi-Tubular Rivets, Full Tubular Rivets, Split Rivets, and End Caps |
| Idioma: | en |
| Edición: | first edition |
| Palabras Clave: | Tornillos; Rosca métrica; Hilos de rosca; Aceptabiblidad; Calibración; Mediciones; Dimensiones |
| Páginas: | 20p. |
| Ingreso de la Info.: | 2011-10-07 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | GAGES AND GAGING FOR UNIFIED SCREW THREADS |
| Código de Doc.: | ANSI/ASME B1.2-1983 |
| Autor Inst.: | The American Society of Mechanical Engineers. ASME |
| Fecha: | 1983 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| País de Origen: | US |
| Objeto: | This Standard provides essential specifications and dimensions for the gages used on Unified inch screw threads UN [unified] and UNR [external threads only] thread form, and covers the specifications and dimensions for the thread gages and measuring equipment listed in Tables 1 and 2. The basic purpose and use of each gage are also described |
| Idioma: | en |
| Edición: | first edition |
| Palabras Clave: | Tornillos; Rosca métrica; Hilos de rosca; Calibración; Mediciones; Dimensiones |
| Páginas: | 179p. |
| Ingreso de la Info.: | 2011-10-06 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | ISO GENERAL-PURPOSE METRIC SCREW THREADS -- GAUGES AND GAUGING |
| Código de Doc.: | ISO 1502 |
| Autor Inst.: | International Organization for Standardization. ISO |
| Fecha: | 1996 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | Gives details for the manufacture and use of gauges for checking ISO general purpose metric screw threads. Specifies the features of gauges which are recommended for checking external and internal screw threads of workpieces. Provides means of distinguishing between threads that comply with the limits of size and those that do not |
| ICS: | 17.040.30; 21.040.10 |
| Idioma: | en |
| Título en otro Idioma: | Filetages métriques ISO pour usages généraux -- Calibres à limites et vérification |
| Edición: | second edition |
| Palabras Clave: | Roscas; Rosca métrica; Hilos de rosca; Tornillos; Mediciones; Calibración; Verificación; Indicadores; Límites; Tamaño |
| Páginas: | 27p. |
| Ingreso de la Info.: | 2011-10-06 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | GENERAL PURPOSE ISO METRIC SCREW THREADS - PART 1: NOMINAL SIZES FOR 1 MM TO 68 MM DIAMETER COARSE PITCH THREADS |
| Código de Doc.: | DIN 13-1 |
| Autor Inst.: | Deutsches Institut Fur Normung. DIN |
| Fecha: | 1999 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| País de Origen: | Deustchland |
| Objeto: | It specifies the nominal sizes for 1 mm to 68 mm diameter coarse pitch threads having the basic profile specified in DIN ISO 68-1 and the nominal profile specified in DIN 13-19 |
| Campo de Aplic.: | This standard applies to general purpose ISO metric screw threads |
| Relac. con otras Normas: | DIN 13-19; DIN 13-20; DIN 2244; DIN ISO 68-1; DIN ISO 724; DIN ISO 965-1 |
| ICS: | 21.040.10 |
| Idioma: | en |
| Título en otro Idioma: | Metrisches ISO-Gewinde allgemeiner Anwendung - Teil 1: Nennmasse für Regelgewinde; Gewinde-Nenndurchmesser von 1 mm bis 68 mm |
| Notas: | Supersedes December 1986 edition |
| Palabras Clave: | Tornillos; Hilos de rosca |
| Páginas: | 4p. |
| Ingreso de la Info.: | 2006-12-11 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | GENERAL PURPOSE ISO METRIC SCREW THREADS - PART 19: NOMINAL PROFILES |
| Código de Doc.: | DIN 13-19 |
| Autor Inst.: | Deutsches Institut Fur Normung. DIN |
| Fecha: | 1999 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| País de Origen: | Deustchland |
| Objeto: | It specifies the nominal profiles for mating external and internal threads with or without clearance on the flank, on which tap dimensions are based |
| Campo de Aplic.: | This standard applies to general purpose ISO metric screw threads having the basic profile specified in DIN ISO 68-1 |
| Relac. con otras Normas: | DIN 2244; DIN ISO 68-1; DIN ISO 724; DIN ISO 965-1 |
| ICS: | 21.040.10 |
| Idioma: | en |
| Título en otro Idioma: | Metrisches ISO-Gewinde allgemeiner Anwendung - Teil 19: Nennprofile |
| Notas: | This Standard together with DIN ISO 68-1, november 1999 edition, supersedes December 1986 edition |
| Palabras Clave: | Tornillos; Hilos de rosca |
| Páginas: | 3p. |
| Ingreso de la Info.: | 2006-12-11 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | GENERAL PURPOSE ISO METRIC SCREW THREADS - PART 52: TOLERANCES FOR MULTI-START THREADS |
| Código de Doc.: | DIN 13-52 |
| Autor Inst.: | Deutsches Institut Fur Normung. DIN |
| Fecha: | 1999 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| País de Origen: | Deustchland |
| Objeto: | It specifies tolerances for multi-start threads having the basic profile specified in DIN ISO 68-1 |
| Campo de Aplic.: | This standard applies to general purpose ISO metric screw threads |
| Relac. con otras Normas: | DIN 2244; DIN 3975; DIN ISO 68-1; DIN ISO 965-1 |
| ICS: | 21.040.10 |
| Idioma: | en |
| Título en otro Idioma: | Metrisches ISO-Gewinde allgemeiner Anwendung - Teil 52: Toleranzen und Profilabweichungen für mehrgängige Gewinde |
| Notas: | Supersedes november 1990 edition |
| Palabras Clave: | Tornillos; Hilos de rosca; Tolerancia |
| Páginas: | 2p. |
| Ingreso de la Info.: | 2006-12-11 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | UNIFIED INCH SCREW THREADS (UN AND UNR THREAD FORM) |
| Código de Doc.: | B1.1 |
| Autor Inst.: | The American Society of Mechanical Engineers. ASME |
| Fecha: | 2003 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| País de Origen: | Estados Unidos |
| Objeto: | This Standard specifies the thread form, series, class, allowance, tolerance, and designation for unified screw threads. (In order to emphasize that unified screw threads are based on inch modules, they may be denoted unified inch screw threads.) Several variations in thread form have been developed for unified threads; however, this Standard covers only UN and UNR thread forms. For easy reference, a metric translation of this Standard has been incorporated as Nonmandatory Appendix C. Nonmandatory Appendices A through E contain useful information that is supplementary to the sections of this Standard |
| Relac. con otras Normas: | ASME B1.2; ASME B1.3; ASME B1.7; ASME B1.30; ASME B47.1; ASME B94.11; ASME Y14.5; ISO 68 |
| Idioma: | en |
| Edición: | first edition |
| Palabras Clave: | Tornillos; Hilos de rosca |
| Páginas: | 178p. |
| Ingreso de la Info.: | 2006-09-06 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | ACME SCREW THREADS |
| Código de Doc.: | B1.5 |
| Autor Inst.: | The American Society of Mechanical Engineers. ASME |
| Fecha: | 1997 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| País de Origen: | Estados Unidos |
| Objeto: | This Standard provides for two general applications of Acme threads: namely, general purpose and centralizing. The limits and tolerances in this Standard relate to single-start Acme threads and may be used, if considered suitable, for multiple-start Acme threads. The latter threads are used to provide relatively fast traversing motion when necessary. The three classes (2G, 3G, and 4G) of general purpose threads have clearances on all diameters for free movement. This thread relies on the thread flanks to maintain concentric operation. The three classes of centralizing threads have a limited clearance at the major diameters of the external and internal threads so that a bearing at the major diameter maintains approximate alignment of the thread axis and prevents wedging on the flanks of the threads |
| Idioma: | en |
| Edición: | first edition |
| Notas: | Reaffirmed Date: 2004. Revision of ASME/ANSI B1.5-1988 |
| Palabras Clave: | Tornillos; Hilos de rosca |
| Páginas: | 124p. |
| Ingreso de la Info.: | 2006-09-04 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | STUB ACME SCREW THREADS |
| Código de Doc.: | ASME/ANSI B1.8-1988 |
| Autor Inst.: | The American Society of Mechanical Engineers. ASME |
| Fecha: | 1988 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| País de Origen: | Estados Unidos |
| Idioma: | en |
| Edición: | first edition |
| Notas: | Revision of ANSI B1.8-1977 |
| Palabras Clave: | Tornillos; Hilos de rosca |
| Páginas: | 30p. |
| Ingreso de la Info.: | 2005-08-30 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
Fin
[Página de Inicio] [Nueva Búsqueda][Página Anterior]