Término solicitado: MAQUINAS DE MEDIR POR COORDENADAS/(65,175,265)
14 Registro/s encontrado/s en CAT+NORMA
| Tipo de Docum.: | serie monográfica |
| Título: | CMM measurement strategies |
| Autor: | Flack, D. |
| Título Ser./Col.: | Measurement Good Practice Guide, no. 41 |
| Autor Inst. Ser./Col.: | National Physical Laboratory. NPL. London. GB |
| Idioma: | eng |
| Datos de Edición: | London. GB. NPL. 2001. |
| Pág./Vol.: | 85p. |
| Notas: | Préstamo permanente a Metrología Dimensional. |
| Descriptores: | Mediciones; Instrumentos de medición; Metrología; Errores; Física; Procedimientos; Máquinas de medir por coordenadas; Estrategias; Métodos de cálculo |
| Ubicación: | 53.083/N21311cm |
| Disponibilidad: | INTI-Córdoba |
| Tipo de Docum.: | serie monográfica |
| Título: | CMM probing |
| Autor: | Flack, D. |
| Título Ser./Col.: | Measurement Good Practice Guide, no. 43 |
| Autor Inst. Ser./Col.: | National Physical Laboratory. NPL. London. GB |
| Idioma: | eng |
| Datos de Edición: | London. GB. NPL. 2001. |
| Pág./Vol.: | 59p. |
| Notas: | Préstamo permanente a Metrología Dimensional. |
| Descriptores: | Mediciones; Instrumentos de medición; Metrología; Errores; Física; Procedimientos; Máquinas de medir por coordenadas; Pruebas |
| Ubicación: | 53.083/N21311c |
| Disponibilidad: | INTI-Córdoba |
| Tipo de Docum.: | serie monográfica |
| Título: | CMM verification |
| Autor: | Flack, D. |
| Título Ser./Col.: | Measurement Good Practice Guide, no. 42 |
| Autor Inst. Ser./Col.: | National Physical Laboratory. NPL. London. GB |
| Idioma: | eng |
| Datos de Edición: | London. GB. NPL. 2001. |
| Pág./Vol.: | 57p. |
| Notas: | Préstamo permanente a B. Gastaldi. |
| Descriptores: | Mediciones; Instrumentos de medición; Metrología; Errores; Física; Procedimientos; Máquinas de medir por coordenadas |
| Ubicación: | 53.083/N21311 |
| Disponibilidad: | INTI-Córdoba |
| Tipo de documento: | NORMA |
| Título: | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) -- ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) -- PART 5: CMMS USING SINGLE AND MULTIPLE STYLUS CONTACTING PROBING SYSTEMS |
| Código de Doc.: | ISO 10360-5 |
| Autor Inst.: | International Organization for Standardization. ISO |
| Fecha: | 2010 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | ISO 10360-5:2010 specifies acceptance and periodic reverification tests of CMM performance with contacting probing systems and is only applicable to CMMs using any type of contacting probing system, a discrete point probing mode, and spherical or hemispherical stylus tip(s). It complements ISO 10360-7, which is the module for CMMs with video probing systems, and ISO 10360-2, which is universal, i.e. not probe-type specific |
| Campo de Aplic.: | ISO 10360-5:2010 applies to CMMs supplied with any of the following: single-stylus probing system; multi-stylus probing systems with fixed multiple styli attached to a single probe (e.g. "star" stylus); multiple probing systems such as those with a stylus for each of their probes; systems with articulating probing; stylus and probe changing systems; manual (non-driven) CMMs. ISO 10360-5:2010 is not applicable to non-contacting probing systems, which require different testing procedures |
| ICS: | 17.040.30 |
| Idioma: | en |
| Título en otro Idioma: | Spécification géométrique des produits (GPS) - Essais de réception et de vérification périodique des machines à mesurer tridimensionnelles (MMT) - Partie 5: MMT utilisant des systèmes de palpage à stylet simple ou à stylets multiples |
| Edición: | Second edition |
| Palabras Clave: | Especificación geométrica de productos; Máquinas de medir por coordenadas; Recepción; Aceptación; Verificación; Mediciones; Sistemas de palpado |
| Páginas: | 30p. |
| Ingreso de la Info.: | 2013-03-20 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) -- ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) -- PART 2: CMMS USED FOR MEASURING LINEAR DIMENSIONS |
| Código de Doc.: | ISO 10360-2:2009 |
| Autor Inst.: | International Organization for Standardization. ISO |
| Fecha: | 2009 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | ISO 10360-2:2009 specifies the acceptance tests for verifying the performance of a coordinate measuring machine (CMM) used for measuring linear dimensions as stated by the manufacturer. It also specifies the reverification tests that enable the user to periodically reverify the performance of the CMM. The acceptance and reverification tests given in ISO 10360-2:2009 are applicable only to Cartesian CMMs using contacting probing systems of any type operating in the discrete-point probing mode. ISO 10360-2:2009 does not explicitly apply to non-Cartesian CMMs or CMMs using optical probing. ISO 10360-2:2009 specifiesï_ performance requirements that can be assigned by the manufacturer or the user of a CMM, the manner of execution of the acceptance and reverification tests to demonstrate the stated requirements, rules for proving conformance, and applications for which the acceptance and reverification tests can be usedThis product replaces:ISO 10360-2:2001 - Geometrical Product Specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 2: CMMs used for measuring size |
| ICS: | 17.040.30 |
| Idioma: | en |
| Título en otro Idioma: | Spécification géométrique des produits (GPS) -- Essais de réception et de vérification périodique des machines à mesurer tridimensionnelles (MMT) -- Partie 2: MMT utilisées pour les mesures de dimensions linéaires |
| Edición: | third edition |
| Palabras Clave: | Especificación geométrica de productos; Máquinas de medir por coordenadas; Recepción; Aceptación; Verificación; Mediciones; Tamaño |
| Páginas: | 31p. |
| Ingreso de la Info.: | 2010-03-19 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) -- ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) -- PART 4: CMMS USED IN SCANNING MEASURING MODE |
| Código de Doc.: | JIS B 7440-4 |
| Autor Inst.: | Japanese Standards Association. JIS |
| Fecha: | 2003 |
| Estado: | |
| País de Origen: | Japan |
| Objeto: | This Standard specifies the acceptance test which verifies that the performance of a CMM used in scanning measuring mode is as stated by the manufacturer. It also specifies the reverification test which enables the user to periodically reverify the performance of a CMM used in scanning measuring mode. The acceptance test and reverification test described in this Standard are applicable only to CMMs capable of performing scannings using any type of contacting probing system(s) |
| Relac. con otras Normas: | JIS B 0641-1; ISO 14253-1; JIS B 7440-1; ISO 10360-1 |
| ICS: | 17.040.30 |
| Idioma: | en |
| Edición: | first edition |
| Notas: | This revision follows the revision of ISO 10360-4:2000 |
| Palabras Clave: | Especificación geométrica de productos; Maquinas de medir por coordenadas; Recepcion; Aceptacion; Verificacion; Escaneo |
| Páginas: | 13p. |
| Ingreso de la Info.: | 2007-10-25 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) -- ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) -- PART 3: CMM'S WITH THE AXIS OF A ROTARY TABLE AS THE FOURTH AXIS |
| Código de Doc.: | JIS B 7440-3 |
| Autor Inst.: | Japanese Standards Association. JIS |
| Fecha: | 2003 |
| Estado: | |
| País de Origen: | Japan |
| Objeto: | This Standard specifies the acceptance test which verifies that the performance of four-axis coordinate measuring machines (CMM) is in accordance with that stated by the manufacturer. It also specifies the reverification test, which enables the user to reverify the performance of a four-axis CMM periodically. The acceptance test and reverification test described in this Standard are applicable only to four-axis machines with three axes for measuring workpiece coordinates, plus a rotary table for orienting the workpiece |
| Relac. con otras Normas: | JIS B 0641-1; ISO 14253-1; JIS B 7440-1; ISO 10360-1 |
| ICS: | 17.040.30 |
| Idioma: | en |
| Edición: | first edition |
| Notas: | This revision follows the revision of ISO 10360-3:2000 |
| Palabras Clave: | Especificación geométrica de productos; Maquinas de medir por coordenadas; Recepcion; Aceptacion; Verificacion; Mesas rotativas |
| Páginas: | 13p. |
| Ingreso de la Info.: | 2007-10-25 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) -- ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) -- PART 6: ESTIMATION OF ERRORS IN COMPUTING GAUSSIAN ASSOCIATED FEATURES |
| Código de Doc.: | JIS B 7440-6 |
| Autor Inst.: | Japanese Standards Association. JIS |
| Fecha: | 2004 |
| Estado: | |
| País de Origen: | Japan |
| Objeto: | This Standard specifies a method for testing software used for computing associated features from coordinate measurements. The features of concern are the line (in two and three dimensions), the plane, the circle (in two and three dimensions), the sphere, the cylinder, the cone and the torus. One or more separate tests are required for each feature claimed to be covered by the software. The test is of the software alone and therefore independent of the coordinate measuring system |
| Relac. con otras Normas: | JIS B 0641-1; ISO 14253-1; JIS B 0672-1; ISO 14660-1; JIS B 0672-2; ISO 14660-2; JIS B 7440-1; ISO 10360-1; JIS B 7440-2; ISO 10360-2 |
| ICS: | 17.040.30 |
| Idioma: | en |
| Edición: | first edition |
| Notas: | This revision follows the revision of ISO 10360-6:2001 |
| Palabras Clave: | Especificación geométrica de productos; Maquinas de medir por coordenadas; Recepcion; Aceptacion; Verificacion; Método de Gauss; Errores; Estimación |
| Páginas: | 22p. |
| Ingreso de la Info.: | 2007-10-25 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) -- ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) -- PART 5: CMMS USING MULTIPLE-STYLUS PROBING SYSTEMS |
| Código de Doc.: | JIS B 7440-5 |
| Autor Inst.: | Japanese Standards Association. JIS |
| Fecha: | 2004 |
| Estado: | |
| País de Origen: | Japan |
| Objeto: | This Standard specifies acceptance and periodic reverification tests of the performance of CMMs having multiple-stylus probing systems, including systems, with fixed multiple-styli attached to a single probe (e.g. "star" stylus), multiple-probing systems such as those with a stylus for each of their probes, and systems with articulating probing |
| Relac. con otras Normas: | JIS B 0641-1; ISO 14253-1; JIS B 7440-1; ISO 10360-1 |
| ICS: | 17.040.30 |
| Idioma: | en |
| Edición: | first edition |
| Notas: | This revision follows the revision of ISO 10360-5:2000 |
| Palabras Clave: | Especificación geométrica de productos; Maquinas de medir por coordenadas; Recepcion; Aceptacion; Verificacion |
| Páginas: | 15p. |
| Ingreso de la Info.: | 2007-10-25 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) -- ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) -- PART 1: VOCABULARY |
| Código de Doc.: | JIS B 7440-1 |
| Autor Inst.: | Japanese Standards Association. JIS |
| Fecha: | 2003 |
| Estado: | |
| País de Origen: | Japan |
| Objeto: | This Standard specifies a vocabulary for coordinate measuring machines (CMM), and their acceptance and reverification tests |
| ICS: | 17.040.30 |
| Idioma: | en |
| Edición: | first edition |
| Notas: | This revision follows the revision of ISO 10360-1:2000 |
| Palabras Clave: | Especificación geométrica de productos; Maquinas de medir por coordenadas; Recepcion; Aceptacion; Verificacion; Terminología |
| Páginas: | 30p. |
| Ingreso de la Info.: | 2007-10-25 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 2: CMMS USED FOR MEASURING SIZE |
| Código de Doc.: | JIS B 7440-2 |
| Autor Inst.: | Japanese Standards Association. JIS |
| Fecha: | 2003 |
| Estado: | |
| País de Origen: | Japan |
| Objeto: | This Standard specifies the acceptance test for verifying that the performance of a CMM used for measuring size is as stated by the manufacturer. It also specifies the reverification test which enables the user to periodically reverify the performance of a CMM used for measuring size |
| Relac. con otras Normas: | JIS B 0641-1; JIS B 0672-1; ISO 14660-1; ISO 14253-1; JIS B 7440-1; ISO 10360-1; JIS B 7506; ISO 3650; International Vocabulary of Basic and General Terms in Metrology (VIM) |
| ICS: | 17.040.30 |
| Idioma: | en |
| Edición: | first edition |
| Notas: | This revision follows the revision of ISO 10360-2:2001 |
| Palabras Clave: | Especificación geométrica de productos; Maquinas de medir por coordenadas; Recepcion; Aceptacion; Verificacion; Mediciones; Tamaño |
| Páginas: | 13p. |
| Ingreso de la Info.: | 2007-10-25 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | METHODS FOR PERFORMANCE EVALUATION OF COORDINATE MEASURING MACHINES |
| Código de Doc.: | ASME B89.4.1-1997 |
| Autor Inst.: | The American Society of Mechanical Engineers. ASME |
| Fecha: | 1997 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| País de Origen: | Estados Unidos |
| Objeto: | This Standard establishes requirements and methods for specifying and testing the performance of coordinate measuring machines (CMMs) having three linear axes perpendicular to each other and up to one rotary axis positioned arbitrarily with respect to these linear axes. In addition to clarifying the performance evaluation of CMMs, this Standard seeks to facilitate performance comparisons among machines by unifying terminology, general machine classification, and the treatment of environmental effects. This Standard attempts to define the simplest testing methods capable of yielding adequate results for the majority of CMMs and is not intended to replace more complete tests that may be suitable for special applications. In particular, this Standard is most applicable to machines used in the point-to-point mode rather than the contour measurement mode. Although this Standard provides checks for most of the parameters relevant to coordinate measuring machines used in a contouring mode, the checks do not actually test contouring accuracy, per se. Additions to this Standard to include contouring performance are in process. This Standard provides definitions of terms applicable to CMMs. These definitions are separated into two parts: first, a glossary covering technical terms used throughout this Standard, and second, an explanation of twelve common machine classifications. The actual specification of CMMs is subdivided into four sections: general machine classification, machine environmental requirements and responses, machine performance, and machine subsystem performance. Machine classification includes machine type, measurement ranges, position resolution, operating mode, and probing method. Environmental specification includes thermal response, electrical requirements, vibration sensitivity, and utility air requirements. Machine performance specification includes repeatability, linear displacement accuracy, ball bar measurement performance, offset probe performance, diagonal displacement performance (large machines), duplex performance (machines used in the duplex mode), rotary axis performance, performance under loaded conditions, and bidirectional length measurement capability. Subsystem performance consists of procedures to evaluate probing performance during point-to-point coordinate acquisition with single and multiple tips. One of the most significant features of this Standard is its treatment of environmental specification and testing. The machine user is assigned clear responsibility for providing a suitable performance test environment, either by meeting the supplier's parameters or by accepting reduced performance. Particular emphasis is placed on the performance degradation caused by temperature variation and vibration. The treatment of thermal effects in this Standard is in conceptual conformance to the provisions of ASME B89.6.2. The key feature of this treatment is the relaxation of machine performance requirements if the thermal environment causes excessive uncertainty or variation in the CMM performance and does not meet the supplier's recommendations regarding thermal parameters. Actual machine performance testing is divided into five major areas: repeatability, linear displacement accuracy, streamlined artifact testing with a ball bar, rotary axis testing, and bidirectional length measurement capability. Supplements to the ball bar testing are provided for large machines and for machines used in the duplex mode. (Note that the supplemental laser interferometer diagonal displacement measurements will give numbers that may be different from those obtained with long ball bars. However, these numbers also adequately reflect the performance of the machine.) Performance tests for machines under loaded conditions are also included. An important feature of these performance tests is the attempt to use normal operating procedures during the tests |
| Idioma: | en |
| Edición: | first edition |
| Notas: | Revision of ASME 89.1.12M-1990 |
| Palabras Clave: | Maquinas de medir por coordenadas; Performance; Evaluacion |
| Páginas: | 78p. |
| Ingreso de la Info.: | 2006-07-18 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) -- ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) -- PART 3: CMMS WITH THE AXIS OF A ROTARY TABLE AS THE FOURTH AXIS |
| Código de Doc.: | ISO 10360-3 |
| Autor Inst.: | International Organization for Standardization. ISO |
| Fecha: | 2000 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | This part of ISO 10360 specifies the acceptance test which verifies that the performance of four-axis coordinate measuring machines (CMM) is in accordance with that stated by the manufacturer. It also specifies the reverification test, which enables the user to reverify the performance of a four-axis CMM periodically |
| Relac. con otras Normas: | ISO 10360-1; ISO 14253-1:1998; International Vocabulary of Basic and General Terms in Metrology (VIM) |
| ICS: | 17.040.30 |
| Idioma: | en |
| Título en otro Idioma: | Spécification géométrique des produits (GPS) - Essais de réception et de vérification périodique des machines a mesurer tridimensionnelles (MMT) - Partie 3: MMT ayant l'axe de rotation d'un plateau tournant comme quatrieme axe |
| Edición: | first edition |
| Palabras Clave: | Especificación geométrica de productos; Maquinas de medir por coordenadas; Recepcion; Aceptacion; Verificacion; Mediciones; Rotacion |
| Páginas: | 12p. |
| Ingreso de la Info.: | 2006-07-10 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) -- ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) -- PART 2: CMMS USED FOR MEASURING SIZE |
| Código de Doc.: | ISO 10360-2:2001 |
| Autor Inst.: | International Organization for Standardization. ISO |
| Fecha: | 2001 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | This part of ISO 10360 specifies the acceptance test for verifying that the performance of a CMM used for measuring size is as stated by the manufacturer. It also specifies the reverification test which enables the user to periodically reverify the performance of a CMM used for measuring size |
| Relac. con otras Normas: | ISO 3650:1998; ISO 10360-1:2000; ISO 14253-1:1998; ISO 14660-1:1999; International Vocabulary of Basic and General Terms in Metrology (VIM) |
| ICS: | 17.040.30 |
| Idioma: | en |
| Título en otro Idioma: | Spécification géométrique des produits (GPS) - Essais de réception et de vérification périodique des machines a mesurer tridimensionnelles (MMT) - Partie 2: MMT utilisées pour les mesures de tailles |
| Edición: | second edition |
| Palabras Clave: | Especificación geométrica de productos; Maquinas de medir por coordenadas; Recepcion; Aceptacion; Verificacion; Mediciones; Tamaño |
| Páginas: | 11p. |
| Ingreso de la Info.: | 2006-07-10 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
Fin
[Página de Inicio] [Nueva Búsqueda][Página Anterior]