| Tipo de documento:
|
NORMA |
| Título:
|
MEASUREMENT OF FLUID FLOW BY MEANS OF PRESSURE DIFFERENTIAL DEVICES INSERTED IN CIRCULAR CROSS-SECTION CONDUITS RUNNING FULL -- PART 5: CONE METERS |
| Código de Doc.:
|
ISO 5167-5 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
2016 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
ISO 5167-5:2016 specifies the geometry and method of use (installation and operating conditions) of cone meters when they are inserted in a conduit running full to determine the flow rate of the fluid flowing in the conduit.As the uncertainty of an uncalibrated cone meter might be too high for a particular application, it might be deemed essential to calibrate the flow meter in accordance with Clause 7.ISO 5167-5:2016 also provides background information for calculating the flow rate and is applicable in conjunction with the requirements given in ISO 5167‑1.ISO 5167-5:2016 is applicable only to cone meters in which the flow remains subsonic throughout the measuring section and where the fluid can be considered as single-phase. Uncalibrated cone meters can only be used within specified limits of pipe size, roughness, β, and Reynolds number. This part of ISO 5167 is not applicable to the measurement of pulsating flow. It does not cover the use of uncalibrated cone meters in pipes sized less than 50 mm or more than 500 mm, or where the pipe Reynolds numbers are below 8 × 104 or greater than 1,2 × 107.A cone meter is a primary device which consists of a cone-shaped restriction held concentrically in the centre of the pipe with the nose of the cone upstream. The design of cone meter defined in this part of ISO 5167 has one or more upstream pressure tappings in the wall, and a downstream pressure tapping positioned in the back face of the cone with the connection to a differential pressure transmitter being a hole through the cone to the support bar, and then up through the support bar.Alternative designs of cone meters are available; however, at the time of writing, there is insufficient data to fully characterize these devices, and therefore, these meters shall be calibrated in accordance with Clause |
| ICS:
|
17.120.10 Flow in closed conduits |
| Idioma:
|
en |
| Título en otro Idioma:
|
Mesure de débit des fluides au moyen d'appareils déprimogènes insérés dans des conduites en charge de section circulaire - Partie 5: Cônes de mesure |
| Edición:
|
First edition |
| Palabras Clave: |
Fluídos;
Caudal;
Mediciones;
Instrumentos de medición;
Presión diferencial;
Conductos;
Placas de orificio
|
| Páginas:
|
15p. |
| Ingreso de la Info.:
|
2017-07-18 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
PLASTICS -- FILM AND SHEETING -- DETERMINATION OF GAS-TRANSMISSION RATE -- PART 2: EQUAL-PRESSURE METHOD |
| Código de Doc.:
|
ISO 15105-2 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
2003 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
ISO 15105-2:2003 specifies a method for the determination of the gas-transmission rate of any plastic material in the form of film, sheeting, laminate, co-extruded material or flexible plastic-coated material. Specific examples, currently in use, of the method are described in the annexes |
| ICS:
|
83.140.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Plastiques -- Film et feuille -- Détermination du coefficient de transmission d'un gaz -- Partie 2: Méthode isobarique |
| Edición:
|
first edition |
| Palabras Clave: |
Plásticos;
Materiales plásticos;
Películas;
Láminas;
Métodos de determinación;
Tasa de transporte de gas;
Presión diferencial
|
| Páginas:
|
15p. |
| Ingreso de la Info.:
|
2012-03-27 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
PLASTICS -- FILM AND SHEETING -- DETERMINATION OF GAS-TRANSMISSION RATE -- PART 1: DIFFERENTIAL-PRESSURE METHODS |
| Código de Doc.:
|
ISO 15105-1 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
2007 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
ISO 15105-1:2007 specifies two methods for determining the gas transmission rate of single-layer plastic film or sheet and multi-layer structures under a differential pressure. One method uses a pressure sensor, the other a gas chromatograph, to measure the amount of gas which permeates through a test specimen |
| ICS:
|
83.140.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Plastiques -- Film et feuille -- Détermination du coefficient de transmission d'un gaz -- Partie 1: Méthodes en pression différentielle |
| Edición:
|
second edition |
| Palabras Clave: |
Plásticos;
Materiales plásticos;
Películas;
Láminas;
Métodos de determinación;
Tasa de transporte de gas;
Presión diferencial;
Sensores de presión;
Cromatografía de gases;
Cromatógrafos
|
| Páginas:
|
12p. |
| Ingreso de la Info.:
|
2012-03-27 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
MEASUREMENT OF FLUID FLOW BY MEANS OF PRESSURE DIFFERENTIAL DEVICES INSERTED IN CIRCULAR CROSS-SECTION CONDUITS RUNNING FULL -- PART 2: ORIFICE PLATES |
| Código de Doc.:
|
ISO 5167-2 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
2003 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
ISO 5167-2:2003 specifies the geometry and method of use (installation and operating conditions) of orifice plates when they are inserted in a conduit running full to determine the flow-rate of the fluid flowing in the conduit. It also provides background information for calculating the flow-rate and is applicable in conjunction with the requirements given in ISO 5167-1 |
| Campo de Aplic.:
|
ISO 5167-2:2003 is applicable to primary devices having an orifice plate used with flange pressure tappings, or with corner pressure tappings, or with D and D/2 pressure tappings. Other pressure tappings such as vena contracta and pipe tappings have been used with orifice plates but are not covered by ISO 5167-2:2003. ISO 5167-2:2003 is applicable only to a flow which remains subsonic throughout the measuring section and where the fluid can be considered as single phase. It is not applicable to the measurement of pulsating flow. It does not cover the use of orifice plates in pipe sizes less than 50 mm or more than 1 000 mm, or for pipe Reynolds numbers below 5000 |
| Relac. con otras Normas:
|
ISO 4006; ISO 5167-1 |
| ICS:
|
17.120.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Mesure de debit des fluides au moyen d'appareils deprimogenes inseres dans des conduites en charge de section circulaire -- Partie 2: Diaphragmes |
| Edición:
|
first edition |
| Palabras Clave: |
Fluídos;
Caudal;
Mediciones;
Instrumentos de medición;
Presión diferencial;
Conductos;
Placas de orificio
|
| Páginas:
|
53p. |
| Ingreso de la Info.:
|
2009-05-11 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
MEASUREMENT OF FLUID FLOW BY MEANS OF PRESSURE DIFFERENTIAL DEVICES INSERTED IN CIRCULAR CROSS-SECTION CONDUITS RUNNING FULL -- PART 1: GENERAL PRINCIPLES AND REQUIREMENTS |
| Código de Doc.:
|
ISO 5167-1 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
2003 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
ISO 5167-1:2003 defines terms and symbols and establishes the general principles for methods of measurement and computation of the flowrate of fluid flowing in a conduit by means of pressure differential devices (orifice plates, nozzles and Venturi tubes) when they are inserted into a circular cross-section conduit running full. ISO 5167-1:2003 also specifies the general requirements for methods of measurement, installation and determination of the uncertainty of the measurement of flowrate. It also defines the general specified limits of pipe size and Reynolds number for which these pressure differential devices are to be used |
| Campo de Aplic.:
|
ISO 5167 (all parts) is applicable only to flow that remains subsonic throughout the measuring section and where the fluid can be considered as single-phase. It is not applicable to the measurement of pulsating flow |
| Relac. con otras Normas:
|
ISO 4006; ISO 5167-2; ISO 5167-3; ISO 5167-4 |
| ICS:
|
17.120.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Mesure de débit des fluides au moyen d'appareils déprimogènes insérés dans des conduites en charge de section circulaire -- Partie 1: Principes généraux et exigences générales |
| Edición:
|
second edition |
| Palabras Clave: |
Fluídos;
Caudal;
Mediciones;
Instrumentos de medición;
Presión diferencial;
Conductos;
Requisitos
|
| Páginas:
|
39p. |
| Ingreso de la Info.:
|
2009-05-05 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
