| Tipo de documento:
|
NORMA |
| Título:
|
ROAD VEHICLES -- TEST METHODS FOR ELECTRICAL DISTURBANCES FROM ELECTROSTATIC DISCHARGE |
| Código de Doc.:
|
ISO 10605 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
2008 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
ISO 10605:2008 specifies the electrostatic discharge (ESD) test methods necessary to evaluate electronic modules intended for vehicle use. It applies to discharges in the following cases: ESD in assembly; ESD caused by service staff; ESD caused by occupants. ISO 10605:2008 describes test procedures for evaluating both electronic modules on the bench and complete vehicles. It also describes a test procedure that classifies the ESD sensitivity of modules for packaging and handling. ISO 10605:2008 applies to all types of road vehicles regardless of the propulsion system (e.g. spark-ignition engine, diesel engine, electric motor) |
| Campo de Aplic.:
|
ESD applied to the device under test (DUT) can directly influence the DUT. ESD applied to neighbouring parts can couple into supply and signal lines of the DUT in the vehicle and/or directly into the DUT. ISO 10605:2008 is based in part on IEC 61000-4-2 and describes vehicle-specific requirements. ISO 10605:2008 does not apply to pyrotechnic modules |
| ICS:
|
43.040.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Véhicules routiers -- Méthodes d'essai des perturbations électriques provenant de décharges électrostatiques |
| Edición:
|
second edition |
| Palabras Clave: |
Vehículos de carretera;
Ingenieria eléctrica;
Métodos de ensayo;
Resistencia eléctrica;
Perturbaciones eléctricas;
Descargas eléctricas;
Electrostática;
Dispositivos eléctricos
|
| Páginas:
|
50p. |
| Ingreso de la Info.:
|
2011-11-21 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
ROAD VEHICLES -- ELECTRICAL DISTURBANCES FROM CONDUCTION AND COUPLING -- PART 3: ELECTRICAL TRANSIENT TRANSMISSION BY CAPACITIVE AND INDUCTIVE COUPLING VIA LINES OTHER THAN SUPPLY LINES |
| Código de Doc.:
|
ISO 7637-3:2007 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
2007 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
ISO 7637-3:2007 establishes a bench top test for the evaluation of the immunity of devices under test (DUTs) to transient transmission by coupling via lines other than supply lines. The test transient pulses simulate both fast and slow transient disturbances, such as those caused by the switching of inductive loads and relay contact bounce. Three test methods are described in ISO 7637-3:2007: the capacitive coupling clamp (CCC) method; the direct capacitive coupling (DCC) method; the inductive coupling clamp (ICC) method. Only one test method need be selected for slow transients and only one method need be selected for fast transients |
| Campo de Aplic.:
|
ISO 7637-3:2007 applies to road vehicles fitted with nominal 12 V, 24 V or 42 V electrical systems. For transient immunity, Annex B provides recommended test severity levels in line with the functional performance status classification (FPSC) principle described in ISO 7637-1 |
| ICS:
|
43.040.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Véhicules routiers -- Perturbations électriques par conduction et par couplage -- Partie 3: Transmission des perturbations électriques par couplage capacitif ou inductif le long des lignes autres que les lignes d'alimentation |
| Edición:
|
second edition |
| Palabras Clave: |
Vehículos de carretera;
Ingenieria eléctrica;
Resistencia eléctrica;
Perturbaciones eléctricas;
Conductividad eléctrica;
Acoplamientos;
Dispositivos eléctricos;
Lineas de suministro eléctrico;
Cargas inductivas;
Cargas capacitivas
|
| Páginas:
|
24p. |
| Ingreso de la Info.:
|
2011-11-21 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-44: PROTECTION FOR SAFETY - PROTECTION AGAINST VOLTAGE DISTURBANCES AND ELECTROMAGNETIC DISTURBANCES |
| Código de Doc.:
|
IEC 60364-4-44:2007 |
| Autor Inst.:
|
International Electrotechnical Commission. IEC/CEI |
| Fecha:
|
2007 |
| Estado: |
|
| Campo de Aplic.:
|
The rules of this Part of IEC 60364 are intended to provide requirements for the safety of electrical installations in the event of voltage disturbances and electromagnetic disturbances generated for different specified reasons. This second edition of IEC 60364-4-44 cancels and replaces the first edition published in 2001, amendment 1 (2003) and amendment 2 (2006). The contents of the corrigendum of May 2010 have been included in this copy |
| ICS:
|
91.140.50 Electricity supply systems; 33.100.10 Emission; 33.100.20 Immunity |
| Título en otro Idioma:
|
Installations électriques des bâtiments - Partie 4-44: Protection pour contre assurer la sécurité - Protection contre les perturbations de tension et les perturbations électromagnetiques |
| Edición:
|
2.0 edition |
| Palabras Clave: |
Edificios;
Instalaciones eléctricas;
Voltaje;
Baja tensión;
Seguridad eléctrica;
Protección;
Medidas de seguridad;
Prevención de accidentes;
Perturbaciones eléctricas;
Perturbaciones electromagnéticas;
Requisitos
|
| Páginas:
|
110p. |
| Ingreso de la Info.:
|
2011-09-21 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
ROAD VEHICLES -- ELECTRICAL DISTURBANCES FROM CONDUCTION AND COUPLING -- PART 2: ELECTRICAL TRANSIENT CONDUCTION ALONG SUPPLY LINES ONLY |
| Código de Doc.:
|
ISO 7637-2 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
2011 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
ISO 7637-2:2011 specifies test methods and procedures to ensure the compatibility to conducted electrical transients of equipment installed on passenger cars and commercial vehicles fitted with 12 V or 24 V electrical systems. It describes bench tests for both the injection and measurement of transients. It is applicable to all types of road vehicles independent of the propulsion system (e.g. spark ignition or diesel engine, electric motor) |
| Campo de Aplic.:
|
Function performance status classification for immunity to transients is also provided |
| ICS:
|
43.040.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Véhicules routiers -- Perturbations électriques par conduction et par couplage -- Partie 2: Perturbations électriques transitoires par conduction uniquement le long des lignes d'alimentation |
| Edición:
|
Third edition |
| Palabras Clave: |
Vehículos de carretera;
Ingeniería eléctrica;
Resistencia eléctrica;
Perturbaciones eléctricas;
Conductividad eléctrica;
Acoplamientos;
Dispositivos eléctricos;
Mediciones;
Transistores
|
| Páginas:
|
43p. |
| Ingreso de la Info.:
|
2011-09-09 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
METHODS OF MEASUREMENT OF THE SUPPRESSION CHARACTERISTICS OF PASSIVE EMC FILTERING DEVICES |
| Código de Doc.:
|
CISPR 17 |
| Autor Inst.:
|
International Electrotechnical Commission. IEC/CEI |
| Fecha:
|
2011 |
| Estado: |
|
| Objeto:
|
CISPR 17:2011 specifies methods to measure the radio interference suppression characteristics of passive EMC filtering devices used in power and signal lines, and in other circuits. The defined methods may also be applied to combinations of over-voltage protection devices and EMC filtering devices. The measurement method covers the frequency range from 9 kHz to several GHz depending on the device and test circuit. The standard describes procedures for laboratory tests (type tests) as well as factory tests. The suppression characteristics of EMC filters and components used for the suppression of EM disturbances, are a function of numerous variables such as impedance of the circuits to which they connect, operating voltage and current, and ambient temperature. This standard specifies uniform test methods that will enable comparison of filtering and suppression characteristics determined by test laboratories or specified by manufacturers. Measurement procedures are provided for unbiased and bias conditions. Measurements under bias conditions are performed to determine potential non-linear behaviour of the EMC filtering devices such as saturation effects in inductors with magnetic cores. This testing serves to show the usability in a specific application (such as frequency converters that produce high amplitudes of common mode pulse current and thus may drive inductors into saturation). Measurement under bias conditions may be omitted if the non-linear behaviour can be determined by other methods (e.g. separate saturation measurement of the inductors used). The first edition of CISPR 17 (1981) prescribed the measurement methods of insertion loss mainly for power-line filters. Today, however, many types of sophisticated EMC filters and suppression components can be found in various electronic devices. Those filters need to be characterized using standardized measurement methods. New methods for measurement of impedance and S-parameters for such EMI devices are included in this second edition |
| Campo de Aplic.:
|
The following significant changes were made with respect to the previous edition:- addition of required measurements with both an average detector and a peak or quasi-peak detector;- addition of methods and limits for the protection of new analogue and digital radio services, which cover the frequency range up to 2 500 MHz;- addition of a new measurement method for components (stripline) as an informative Annex G;- addition of the contents of CISPR 21 as Annex H; CISPR 21 in its entirety now becomes obsolete;- deletion of narrowband / broadband determination;- deletion of the Annex on rod antenna characterisation (this is now covered by CISPR 16-1-4);- deletion of the Annex on characterisation of shielded enclosure (CISPR 25 will be amended when the CISPR/D / CISPR/A Joint Task Force on chamber validation finishes its work). The contents of the corrigendum of January 2009 have been included in this copy |
| ICS:
|
33.100.01 Electromagnetic compatibility in general |
| Idioma:
|
en,fr |
| Título en otro Idioma:
|
Méthodes de mesure des caractéristiques d'antiparasitage des dispositifs de filtrage CEM passifs |
| Edición:
|
2.0 edition |
| Palabras Clave: |
Compatibilidad electromagnética;
Mediciones;
Radiofrecuencia;
Dispositivos;
Interferencias;
Filtración;
Perturbaciones eléctricas;
Métodos de medición
|
| Páginas:
|
135p. |
| Ingreso de la Info.:
|
2011-08-04 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
ROAD VEHICLES -- ELECTRICAL DISTURBANCES FROM CONDUCTION AND COUPLING -- PART 1: DEFINITIONS AND GENERAL CONSIDERATIONS - AMENDMENT 1 |
| Código de Doc.:
|
ISO 7637-1:2002/Amd 1:2008 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
2008 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
This part of ISO 7637 defines the basic terms relating to electrical disturbances from conduction and coupling used in its other parts, and gives general information on the whole of ISO 7637 and common to all parts |
| ICS:
|
43.040.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Véhicules routiers -- Perturbations électriques par conduction et par couplage -- Partie 1: Définitions et généralités - Amendement 1 |
| Edición:
|
second edition |
| Palabras Clave: |
Vehículos de carretera;
Ingeniería eléctrica;
Resistencia eléctrica;
Perturbaciones eléctricas;
Conductividad eléctrica;
Acoplamientos;
Terminología;
Requisitos
|
| Páginas:
|
7p. |
| Ingreso de la Info.:
|
2011-04-12 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
ROAD VEHICLES -- ELECTRICAL DISTURBANCES FROM CONDUCTION AND COUPLING -- PART 2: ELECTRICAL TRANSIENT CONDUCTION ALONG SUPPLY LINES ONLY - AMENDEMENT 1 |
| Código de Doc.:
|
ISO 7637-2:2004/Amd 1:2008 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
2008 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
ISO 7637-2:2004 specifies bench tests for testing the compatibility to conducted electrical transients of equipment installed on passenger cars and light commercial vehicles fitted with a 12 V electrical system or commercial vehicles fitted with a 24 V electrical system -- for both injection and the measurement of transients. Failure mode severity classification for immunity to transients is also given. It is applicable to these types of road vehicle, independent of the propulsion system (e.g. spark ignition or diesel engine, or electric motor |
| ICS:
|
43.040.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Véhicules routiers -- Perturbations électriques par conduction et par couplage -- Partie 2: Perturbations électriques transitoires par conduction uniquement le long des lignes d'alimentation - Amendement 1 |
| Edición:
|
first edition |
| Palabras Clave: |
Vehículos de carretera;
Ingeniería eléctrica;
Resistencia eléctrica;
Perturbaciones eléctricas;
Conductividad eléctrica;
Acoplamientos;
Dispositivos eléctricos;
Lineas de suministro eléctrico
|
| Páginas:
|
7p. |
| Ingreso de la Info.:
|
2011-04-12 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
ROAD VEHICLES -- ELECTRICAL DISTURBANCE BY CONDUCTION AND COUPLING -- PART 3: VEHICLES WITH NOMINAL 12 V OR 24 V SUPPLY VOLTAGE -- ELECTRICAL TRANSIENT TRANSMISSION BY CAPACITIVE AND INDUCTIVE COUPLING VIA LINES OTHER THAN SUPPLY LINES |
| Código de Doc.:
|
ISO 7637-3:1995 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
1995 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
Establishes a basis for the evaluation of the EMC of electronic instruments, devices and equipment in vehicles against transient transmission by capacitive and inductive coupling via lines other than the supply lines. Test is intended for the demonstration of the immunity of the above mentioned items against disturbances such as those caused by switching |
| Relac. con otras Normas:
|
ISO 6722-3; ISO 7637-1; ISO 7637-2 |
| ICS:
|
43.040.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Véhicules routiers -- Perturbations électriques par conduction et par couplage -- Partie 3: Véhicules à tension nominale de 12 V ou 24 V -- Transmission des perturbations électriques par couplage capacitif ou inductif le long des lignes autres que les lignes d'alimentation |
| Edición:
|
first edition |
| Palabras Clave: |
Vehículos de carretera;
Ingeniería eléctrica;
Resistencia eléctrica;
Perturbaciones eléctricas;
Conductividad eléctrica;
Acoplamientos;
Dispositivos eléctricos;
Lineas de suministro eléctrico;
Cargas inductivas;
Cargas capacitivas
|
| Páginas:
|
15p. |
| Ingreso de la Info.:
|
2011-04-12 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
VEHICULOS DE CARRETERA. PERTURBACIONES ELECTRICAS POR CONDUCCION Y POR ACOPLAMIENTO. PARTE 3: VEHICULOS INDUSTRIALES CON TENSION NOMINAL DE 24 V. TRANSMISION DE LAS PERTURBACIONES ELECTRICAS A LO LARGO DE LA LINEA DE ALIMENTACION |
| Código de Doc.:
|
UNE 26438-3 |
| Autor Inst.:
|
Asociación Española de Normalización y Certificación. AENOR |
| Fecha:
|
1994 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| País de Origen:
|
España |
| Objeto:
|
Define los métodos y procedimiento de ensayo permitiendo asegurar la compatibilidad a los transitorios eléctricos de los equipos instalados en los vehículos industriales teniendo una alimentación de 24 V. Se describen los bancos de ensayo para la inyección y medida de los transitorios |
| Relac. con otras Normas:
|
UNE 26-115-3 |
| ICS:
|
43.040.10 Equipos eléctricos y electrónicos |
| Idioma:
|
es |
| Título en otro Idioma:
|
Road vehicles. Electrical disturbance by conduction and coupling. Part 3: Commercial vehicles with nominal 24 V supply voltage. Electrical trasient conduction along supply lines only |
| Edición:
|
primera edición |
| Palabras Clave: |
Vehículos;
Automotores;
Carreteras;
Perturbaciones eléctricas;
Acoplamientos;
Métodos de ensayo;
Compatibilidad;
Ciurcuitos eléctricos;
Transitorios;
Voltaje
|
| Páginas:
|
18p. |
| Ingreso de la Info.:
|
2010-02-03 |
