| Tipo de documento:
|
NORMA |
| Título:
|
ROAD VEHICLES -- 60 V AND 600 V SINGLE-CORE CABLES -- DIMENSIONS, TEST METHODS AND REQUIREMENTS |
| Código de Doc.:
|
ISO 6722 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
2006 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
ISO 6722:2006 specifies the dimensions, test methods, and requirements for single-core 60 V cables intended for use in road vehicle applications where the nominal system voltage is equal to or less than (60 V d.c. or 25 V a.c.). It also specifies additional test methods and/or requirements for 600 V cables intended for use in road vehicle applications where the nominal system voltage is greater than (60 V d.c. or 25 V a.c.) to equal to or less than (600 V d.c. or 600 V a.c.). It also applies to individual cores in multi-core cables |
| ICS:
|
43.040.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Véhicules routiers -- Câbles monoconducteurs de 60 V et 600 V -- Dimensions, méthodes d'essai et exigences |
| Edición:
|
second edition |
| Palabras Clave: |
Vehículos de carretera;
Ingenieria eléctrica;
Métodos de ensayo;
Voltaje;
Cables;
Dimensiones
|
| Páginas:
|
43p. |
| Ingreso de la Info.:
|
2012-02-22 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
ROAD VEHICLES -- TEST METHODS FOR ELECTRICAL DISTURBANCES FROM ELECTROSTATIC DISCHARGE |
| Código de Doc.:
|
ISO 10605 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
2008 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
ISO 10605:2008 specifies the electrostatic discharge (ESD) test methods necessary to evaluate electronic modules intended for vehicle use. It applies to discharges in the following cases: ESD in assembly; ESD caused by service staff; ESD caused by occupants. ISO 10605:2008 describes test procedures for evaluating both electronic modules on the bench and complete vehicles. It also describes a test procedure that classifies the ESD sensitivity of modules for packaging and handling. ISO 10605:2008 applies to all types of road vehicles regardless of the propulsion system (e.g. spark-ignition engine, diesel engine, electric motor) |
| Campo de Aplic.:
|
ESD applied to the device under test (DUT) can directly influence the DUT. ESD applied to neighbouring parts can couple into supply and signal lines of the DUT in the vehicle and/or directly into the DUT. ISO 10605:2008 is based in part on IEC 61000-4-2 and describes vehicle-specific requirements. ISO 10605:2008 does not apply to pyrotechnic modules |
| ICS:
|
43.040.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Véhicules routiers -- Méthodes d'essai des perturbations électriques provenant de décharges électrostatiques |
| Edición:
|
second edition |
| Palabras Clave: |
Vehículos de carretera;
Ingenieria eléctrica;
Métodos de ensayo;
Resistencia eléctrica;
Perturbaciones eléctricas;
Descargas eléctricas;
Electrostática;
Dispositivos eléctricos
|
| Páginas:
|
50p. |
| Ingreso de la Info.:
|
2011-11-21 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
ROAD VEHICLES -- ELECTRICAL DISTURBANCES FROM CONDUCTION AND COUPLING -- PART 3: ELECTRICAL TRANSIENT TRANSMISSION BY CAPACITIVE AND INDUCTIVE COUPLING VIA LINES OTHER THAN SUPPLY LINES |
| Código de Doc.:
|
ISO 7637-3:2007 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
2007 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
ISO 7637-3:2007 establishes a bench top test for the evaluation of the immunity of devices under test (DUTs) to transient transmission by coupling via lines other than supply lines. The test transient pulses simulate both fast and slow transient disturbances, such as those caused by the switching of inductive loads and relay contact bounce. Three test methods are described in ISO 7637-3:2007: the capacitive coupling clamp (CCC) method; the direct capacitive coupling (DCC) method; the inductive coupling clamp (ICC) method. Only one test method need be selected for slow transients and only one method need be selected for fast transients |
| Campo de Aplic.:
|
ISO 7637-3:2007 applies to road vehicles fitted with nominal 12 V, 24 V or 42 V electrical systems. For transient immunity, Annex B provides recommended test severity levels in line with the functional performance status classification (FPSC) principle described in ISO 7637-1 |
| ICS:
|
43.040.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Véhicules routiers -- Perturbations électriques par conduction et par couplage -- Partie 3: Transmission des perturbations électriques par couplage capacitif ou inductif le long des lignes autres que les lignes d'alimentation |
| Edición:
|
second edition |
| Palabras Clave: |
Vehículos de carretera;
Ingenieria eléctrica;
Resistencia eléctrica;
Perturbaciones eléctricas;
Conductividad eléctrica;
Acoplamientos;
Dispositivos eléctricos;
Lineas de suministro eléctrico;
Cargas inductivas;
Cargas capacitivas
|
| Páginas:
|
24p. |
| Ingreso de la Info.:
|
2011-11-21 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
ROAD VEHICLES -- ELECTRICAL DISTURBANCES FROM CONDUCTION AND COUPLING -- PART 2: ELECTRICAL TRANSIENT CONDUCTION ALONG SUPPLY LINES ONLY |
| Código de Doc.:
|
ISO 7637-2 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
2011 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
ISO 7637-2:2011 specifies test methods and procedures to ensure the compatibility to conducted electrical transients of equipment installed on passenger cars and commercial vehicles fitted with 12 V or 24 V electrical systems. It describes bench tests for both the injection and measurement of transients. It is applicable to all types of road vehicles independent of the propulsion system (e.g. spark ignition or diesel engine, electric motor) |
| Campo de Aplic.:
|
Function performance status classification for immunity to transients is also provided |
| ICS:
|
43.040.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Véhicules routiers -- Perturbations électriques par conduction et par couplage -- Partie 2: Perturbations électriques transitoires par conduction uniquement le long des lignes d'alimentation |
| Edición:
|
Third edition |
| Palabras Clave: |
Vehículos de carretera;
Ingeniería eléctrica;
Resistencia eléctrica;
Perturbaciones eléctricas;
Conductividad eléctrica;
Acoplamientos;
Dispositivos eléctricos;
Mediciones;
Transistores
|
| Páginas:
|
43p. |
| Ingreso de la Info.:
|
2011-09-09 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
ROAD VEHICLES -- ELECTRICAL DISTURBANCES FROM CONDUCTION AND COUPLING -- PART 1: DEFINITIONS AND GENERAL CONSIDERATIONS - AMENDMENT 1 |
| Código de Doc.:
|
ISO 7637-1:2002/Amd 1:2008 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
2008 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
This part of ISO 7637 defines the basic terms relating to electrical disturbances from conduction and coupling used in its other parts, and gives general information on the whole of ISO 7637 and common to all parts |
| ICS:
|
43.040.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Véhicules routiers -- Perturbations électriques par conduction et par couplage -- Partie 1: Définitions et généralités - Amendement 1 |
| Edición:
|
second edition |
| Palabras Clave: |
Vehículos de carretera;
Ingeniería eléctrica;
Resistencia eléctrica;
Perturbaciones eléctricas;
Conductividad eléctrica;
Acoplamientos;
Terminología;
Requisitos
|
| Páginas:
|
7p. |
| Ingreso de la Info.:
|
2011-04-12 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
ROAD VEHICLES -- ELECTRICAL DISTURBANCES FROM CONDUCTION AND COUPLING -- PART 2: ELECTRICAL TRANSIENT CONDUCTION ALONG SUPPLY LINES ONLY - AMENDEMENT 1 |
| Código de Doc.:
|
ISO 7637-2:2004/Amd 1:2008 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
2008 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
ISO 7637-2:2004 specifies bench tests for testing the compatibility to conducted electrical transients of equipment installed on passenger cars and light commercial vehicles fitted with a 12 V electrical system or commercial vehicles fitted with a 24 V electrical system -- for both injection and the measurement of transients. Failure mode severity classification for immunity to transients is also given. It is applicable to these types of road vehicle, independent of the propulsion system (e.g. spark ignition or diesel engine, or electric motor |
| ICS:
|
43.040.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Véhicules routiers -- Perturbations électriques par conduction et par couplage -- Partie 2: Perturbations électriques transitoires par conduction uniquement le long des lignes d'alimentation - Amendement 1 |
| Edición:
|
first edition |
| Palabras Clave: |
Vehículos de carretera;
Ingeniería eléctrica;
Resistencia eléctrica;
Perturbaciones eléctricas;
Conductividad eléctrica;
Acoplamientos;
Dispositivos eléctricos;
Lineas de suministro eléctrico
|
| Páginas:
|
7p. |
| Ingreso de la Info.:
|
2011-04-12 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento:
|
NORMA |
| Título:
|
ROAD VEHICLES -- ELECTRICAL DISTURBANCE BY CONDUCTION AND COUPLING -- PART 3: VEHICLES WITH NOMINAL 12 V OR 24 V SUPPLY VOLTAGE -- ELECTRICAL TRANSIENT TRANSMISSION BY CAPACITIVE AND INDUCTIVE COUPLING VIA LINES OTHER THAN SUPPLY LINES |
| Código de Doc.:
|
ISO 7637-3:1995 |
| Autor Inst.:
|
International Organization for Standardization. ISO |
| Fecha:
|
1995 |
| Estado: |
Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto:
|
Establishes a basis for the evaluation of the EMC of electronic instruments, devices and equipment in vehicles against transient transmission by capacitive and inductive coupling via lines other than the supply lines. Test is intended for the demonstration of the immunity of the above mentioned items against disturbances such as those caused by switching |
| Relac. con otras Normas:
|
ISO 6722-3; ISO 7637-1; ISO 7637-2 |
| ICS:
|
43.040.10 |
| Idioma:
|
en |
| Título en otro Idioma:
|
Véhicules routiers -- Perturbations électriques par conduction et par couplage -- Partie 3: Véhicules à tension nominale de 12 V ou 24 V -- Transmission des perturbations électriques par couplage capacitif ou inductif le long des lignes autres que les lignes d'alimentation |
| Edición:
|
first edition |
| Palabras Clave: |
Vehículos de carretera;
Ingeniería eléctrica;
Resistencia eléctrica;
Perturbaciones eléctricas;
Conductividad eléctrica;
Acoplamientos;
Dispositivos eléctricos;
Lineas de suministro eléctrico;
Cargas inductivas;
Cargas capacitivas
|
| Páginas:
|
15p. |
| Ingreso de la Info.:
|
2011-04-12 |
|
|
Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
