Término solicitado: PRODUCTOS DE PETROLEO/(65,175,265)
43 Registro/s encontrado/s en CAT+NORMA
| Tipo de Docum.: | informe |
| Título: | El abecé del petróleo y del gas en el mundo y en la Argentina |
| Autor Instit.: | Instituto Argentino del Petróleo y del Gas. IAPG. Buenos Aires. AR |
| Idioma: | spa |
| Datos de Edición: | 3 ed.. Buenos Aires. AR. IAPG. 2009. |
| Pág./Vol.: | 172p. |
| Notas: | Donación de Presidencia: Ing. Enrique Martínez. |
| Descriptores: | Industria petrolera; Industria del gas; Hidrocarburos; Carbón mineral; Petróleo; Gas natural; Extracción del petróleo; Abastecimiento; Pozos petrolíferos; Excavaciones; Producción; Productos de petróleo; Rutas; Transporte; Redes de distribución; Refinamiento; Separación; Petroquímica; Comercialización; Medio ambiente; Energías no convencionales |
| Ubicación: | 665.6/.7/I59/P |
| Disponibilidad: | Préstamo |
| Tipo de Docum.: | libro |
| Título: | Significance of tests for petroleum products |
| Autor: | Rand, Salvatore J.. ed. |
| Idioma: | eng |
| Datos de Edición: | 8.ed.. West Conshohocken. US. ASTM. 2010. |
| Pág./Vol.: | vii, 341p. |
| Notas: | Ejemplar en préstamo permanente a INTI-Química. |
| Descriptores: | Petróleo; Productos de petróleo; Industria petrolera; Combustibles; Motores de combustion interna; Motores Diesel; Turbinas a gas; Combustibles de aviación; Combustibles sólidos; Coque; Carbón; Grafito; Muestreo; Combustibles líquidos; Combustibles gaseosos; Hidrocarburos; Solventes; Aceites minerales; Lubricantes; Caucho; Grasas; Engrase; Ceras; Ensayos; Impactos ambientales; Aseguramiento de la Calidad |
 Ver más
| |
| Ubicación: | 622.323/R187; CEQUIPE/315 |
| Disponibilidad: | Préstamo |
| Tipo de Docum.: | documento de conferencia |
| Título: | Potenciometría aplicada a TAN y TBN en derivados del petróleo |
| Autor: | Puelles, M.M.; Acosta, O.H.; Ilgisonis, A.; Schvartz, M.; Borinsky, M. |
| Autor Instit.: | INTI-Química. Buenos Aires. AR |
| Reunión: | Instituto Nacional de Tecnología Industrial. INTI. Buenos Aires. AR, Jornadas de desarrollo e innovación tecnológica, 6, Química, nuevos servicios, Parque Tecnológico Miguelete. AR, 2007 |
| Idioma: | spa |
| Datos de Edición: | Buenos Aires. AR. INTI. 2007. |
| Pág./Vol.: | 3p. |
| Unidad técnica: | INTI-Química. |
| Descriptores: | Productos de petróleo; Potenciometría; Acidos; Bases-Química; Mediciones; Métodos de determinación |
| Ver Documento
| |
Trabajo de INTI |
|
| Ubicación: | PEI/2 |
| Disponibilidad: | Consulta in situ |
| Tipo de Docum.: | informe |
| Título: | Envases para salsa de tomate. Un análisis comparativo de la ecoeficiencia; el caso de la planta Frutos de Cuyo SA del Grupo ARCOR |
| Autor: | Garrido, Guillermo; Tuninetti, Leticia |
| Autor Instit.: | INTI-Córdoba. AR |
| Idioma: | spa |
| Datos de Edición: | Córdoba. AR. INTI-Córdoba. 2012. |
| Pág./Vol.: | 111p. |
| Notas: | Enmarcado en Convenio de Confidencialidad. Sólo podrá ser consultado por personal del INTI, en sala de la Biblioteca Central. No se pueden solicitar copias . |
| Unidad técnica: | INTI-Córdoba. |
| Descriptores: | Envases; Tomates; Salsas; Eficiencia; Ecología; Contaminación de alimentos; Contaminación ambiental; Impactos ambientales; Metodología; Métodos de análisis; Envases flexibles; Cartón; Hojalata; Transporte; Energía; Productos de petróleo; Petróleo; Gas natural; Etileno; Energía eléctrica; Fabricación; Procesos industriales; Procesos de envasado; Costos; Consumo de energía; Residuos; Enfermedades ocupacionales; Higiene industrial; Toxicidad; Desechos sólidos |
Trabajo de INTI |
|
| Ubicación: | 4706 |
| Disponibilidad: | Consulta in situ |
| Tipo de Docum.: | libro |
| Título: | Petroleum refinery engineering |
| Autor: | Nelson, W.L. |
| Título Ser./Col.: | Chemical engineering series |
| Idioma: | eng |
| Datos de Edición: | 4.ed.. New York, US; Toronto, CA; London. GB. McGraw-Hill. 1958. |
| Pág./Vol.: | 960p. |
| Descriptores: | Petróleo; Refinería; Refinamiento; Composición química; Métodos de ensayo; Aceites minerales; Productos de petróleo; Propiedades físicas; Destilación; Destilerías; Corrosión; Metales; Solventes; Extracción; Parafinas; Mecánica de los fluidos; Combustión; Evaporación; Condensación; Transferencia de calor; Intercambiadores de calor; Tratamientos térmicos; Descomposición; Gas natural; Gases |
| Ubicación: | CEQUIPE/212/Metales y A.Inorgánico |
| Disponibilidad: | CEQUIPE |
| Tipo de Docum.: | conferencia |
| Título: | Trabajos |
| Reunión: | Conferencia internacional del combustible en la industria, 2, Buenos Aires. AR, 1966 |
| Idioma: | spa |
| Datos de Edición: | Buenos Aires. AR. s.ed. s.f. |
| Pág./Vol.: | pag. varía. |
| Descriptores: | Combustibles; Energía; Calor; Vapor; Turbinas; Abastecimiento de energía electrica; PYME; Turbinas de vapor; Turbinas a gas; Análisis económico; Economía de la energía; Resinas; Intercambio de iones; Tratamiento de aguas; Calderas; Inhibidores de corrosión; Industria cerámica; Carbón; Vanadio; Combustibles; Productos de petróleo; Corrosión; Metalografía; Ensayos no destructivos |
Trabajo de INTI |
|
| Ubicación: | 1418 |
| Disponibilidad: | Consulta in situ |
| Tipo de Docum.: | conferencia |
| Título: | Trabajos |
| Reunión: | Conferencia Internacional Combustible en la Industria, 1, Buenos Aires. AR, 1961 |
| Idioma: | spa |
| Datos de Edición: | Buenos Aires. AR. s.e. s.f. |
| Pág./Vol.: | 3v., ilus. |
| Unidad técnica: | CIPUEC. |
| Descriptores: | Combustibles; Productos de petróleo; Siderurgia; Calefacción; Control de calidad; Materiales refractarios; Procesos industriales; Calderas de vapor; Gas natural; Turbinas a gas; Control del humo; Chimeneas; Escape; Vehículos; Transporte; Combustibles; Diseño industrial; Sistemas mecánicos; Temperatura; Economía de la energía; Turbinas; Trazas de sustancias; Metales; Gases; Combustión; Recuperación del calor; Centrales térmicas; Tratamiento de efluentes; Quemadores; Refrigeración; Almacenamiento; Energía eólica |
Trabajo de INTI |
|
| Ubicación: | 1389; 1390; 1391 |
| Disponibilidad: | Consulta in situ |
| Tipo de documento: | NORMA |
| Título: | STANDARD TEST METHOD FOR ACID AND BASE NUMBER BY COLOR-INDICATOR TITRATION |
| Código de Doc.: | ASTM D974 - 14 |
| Autor Inst.: | American Society for Testing and Materials. ASTM International |
| Fecha: | 2014 |
| Estado: | |
| País de Origen: | US |
| Objeto: | This test method covers the determination of acidic or basic constituents (Note 1) in petroleum products2 and lubricants soluble or nearly soluble in mixtures of toluene and isopropyl alcohol. It is applicable for the determination of acids or bases whose dissociation constants in water are larger than 10−9; extremely weak acids or bases whose dissociation constants are smaller than 10−9 do not interfere. Salts react if their hydrolysis constants are larger than 10−9.In new and used oils, the constituents considered to have acidic characteristics include organic and inorganic acids, esters, phenolic compounds, lactones, resins, salts of heavy metals, and addition agents such as inhibitors and detergents. Similarly, constituents considered to have basic properties include organic and inorganic bases, amino compounds, salts of weak acids (soaps), basic salts of polyacidic bases, salts of heavy metals, and addition agents such as inhibitors and detergents.This test method is not suitable for measuring the basic constituents of many basic additive-type lubricating oils. Test Method D4739 can be used for this purpose.This test method can be used to indicate relative changes that occur in an oil during use under oxidizing conditions. Although the titration is made under definite equilibrium conditions, the method does not measure an absolute acidic or basic property that can be used to predict performance of an oil under service conditions. No general relationship between bearing corrosion and acid or base numbers is known. Oils, such as many cutting oils, rustproofing oils, and similar compounded oils, or excessively dark-colored oils, that cannot be analyzed for acid number by this test method due to obscurity of the color-indicator end point, can be analyzed by Test Method D664. The acid numbers obtained by this color-indicator test method need not be numerically the same as those obtained by Test Method D664, the base numbers obtained by this color indicator test method need not be numerically the same as those obtained by Test Method D4739, but they are generally of the same order of magnitude. |
| Campo de Aplic.: | The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use |
| ICS: | 75.080 (Petroleum products in general); 75.100 (Lubricants, industrial oils and related products) |
| Otros Códigos: | UNSPSC Code 15101500(Petroleum and distillates); 15121500(Lubricating preparations) |
| Idioma: | en |
| Notas: | Active Standard ASTM D974, Book of Standards Volume:05.01 |
| Palabras Clave: | Productos de petróleo; Aceites lubricantes; Lubricantes; Métodos de ensayo; Acidos; Bases-Química; Color; Análisis volumétrico |
| Páginas: | 7p. |
| Ingreso de la Info.: | 2016-01-20 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | PETROLEUM AND LIQUID PETROLEUM PRODUCTS -- CALIBRATION OF VERTICAL CYLINDRICAL TANKS -- PART 3: OPTICAL-TRIANGULATION METHOD |
| Código de Doc.: | ISO 7507-3:2006 |
| Autor Inst.: | International Organization of Standardization. ISO |
| Fecha: | 2006 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | ISO 7507-3:2006 specifies a calibration procedure for application to tanks above 8 m in diameter with cylindrical courses that are substantially vertical. It provides a method for determining the volumetric quantity contained within a tank at gauged liquid levels. The measurements required to determine the radius are made either internally or externally. The external method is applicable only to tanks that are free of insulation |
| Campo de Aplic.: | ISO 7507-3:2006 is suitable for tanks tilted up to a 3 % deviation from the vertical, provided that a correction is applied for the measured tilt as described in ISO 7507-1 |
| ICS: | 75.180.30 |
| Idioma: | en |
| Título en otro Idioma: | Pétrole et produits pétroliers liquides- jaugeage des réservoirs cylindriques verticaux. Partie 3: méthode par triangulation optique |
| Edición: | Second edition |
| Palabras Clave: | Petroleo; Productos de petroleo; Tanques; Calibracion; Mediciones ópticas; Métodos ópticos |
| Páginas: | 38p. |
| Ingreso de la Info.: | 2013-06-05 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | STANDARD TEST METHOD FOR KINEMATIC VISCOSITY OF TRANSPARENT AND OPAQUE LIQUIDS (AND CALCULATION OF DYNAMIC VISCOSITY) |
| Código de Doc.: | ASTM D445-14e2 |
| Autor Inst.: | American Society for Testing and Materials. ASTM International |
| Fecha: | 2015 |
| Estado: | |
| País de Origen: | US |
| Objeto: | This test method specifies a procedure for the determination of the kinematic viscosity, ν, of liquid petroleum products, both transparent and opaque, by measuring the time for a volume of liquid to flow under gravity through a calibrated glass capillary viscometer. The dynamic viscosity, η, can be obtained by multiplying the kinematic viscosity, ν, by the density, ρ, of the liquid. The result obtained from this test method is dependent upon the behavior of the sample and is intended for application to liquids for which primarily the shear stress and shear rates are proportional (Newtonian flow behavior). If, however, the viscosity varies significantly with the rate of shear, different results may be obtained from viscometers of different capillary diameters. The procedure and precision values for residual fuel oils, which under some conditions exhibit non-Newtonian behavior, have been included. The range of kinematic viscosities covered by this test method is from 0.2 mm2/s to 300 000 mm2/s (see Table A1.1) at all temperatures (see 6.3 and 6.4). The precision has only been determined for those materials, kinematic viscosity ranges and temperatures as shown in the footnotes to the precision section. The values stated in SI units are to be regarded as standard. The SI unit used in this test method for kinematic viscosity is mm2/s, and the SI unit used in this test method for dynamic viscosity is mPa·s. For user reference, 1 mm2/s = 10-6 m2/s = 1 cSt and 1 mPa·s = 1 cP = 0.001 Pa·s. WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| ICS: | 17.060 (Measurement of volume, mass, density, viscosity); 75.080 (Petroleum products in general) |
| Otros Códigos: | UNSPSC Code 15101500(Petroleum and distillates) |
| Idioma: | en |
| Notas: | Active Standard: D445 - 15 |
| Palabras Clave: | Viscosidad; Métodos de ensayo; Productos de petróleo; Pétroleo; Viscosímetros; Cinética; Mediciones; Mediciones de volumen; Métodos de cálculo |
| Páginas: | 13p. |
| Ingreso de la Info.: | 2015-04-06 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | STANDARD SPECIFICATION FOR DIESEL FUEL OILS |
| Código de Doc.: | ASTM D975 - 14b |
| Autor Inst.: | American Society for Testing and Materials. ASTM International |
| Fecha: | 2015 |
| Estado: | |
| País de Origen: | US |
| Objeto: | This specification covers seven grades of diesel fuel oils suitable for various types of diesel engines. These grades are: Grade No. 1-D S15; Grade No. 1-D S500; Grade No. 1-D S5000; Grade No. 2-D S15; Grade No. 2-D S500; Grade No. 2-D S5000; and Grade No. 4-D. The requirements specified for diesel fuel oils shall be determined in accordance with the following test methods: flash point; cloud point; water and sediment; carbon residue; ash; distillation; viscosity; sulfur; copper corrosion; cetane number; cetane index; aromaticity; lubricity; and conductivity.This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date |
| ICS: | 75.160.20 (Liquid fuels) |
| Otros Códigos: | UNSPSC Code 15101505(Diesel fuel) |
| Idioma: | en |
| Notas: | Active Standard: D975 - 15 |
| Palabras Clave: | Combustibles Diesel; Biocombustibles; Petróleo; Productos de petróleo; Especificaciones |
| Páginas: | 27p. |
| Ingreso de la Info.: | 2015-04-06 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | PETROLEUM AND NATURAL GAS INDUSTRIES -- COMPLETION FLUIDS AND MATERIALS -- PART 2: MEASUREMENT OF PROPERTIES OF PROPPANTS USED IN HYDRAULIC FRACTURING AND GRAVEL-PACKING OPERATIONS- ADDITION OF ANNEX B: PROPPAND SPECIFICATION |
| Código de Doc.: | ISO 13503-2:2006/Amd 1 |
| Autor Inst.: | International Organization of Standardization. ISO |
| Fecha: | 2009 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| ICS: | 75.100 |
| Idioma: | en |
| Título en otro Idioma: | Industries du pétrole et du gaz naturel. Fluides de complétion et matériaux. Mesurage des propriétés des matériaux de soutènement utilisés dans les opérations de fracturation hydraulique et de remplissage de gravier |
| Edición: | First edition |
| Palabras Clave: | Petroleo; Productos de petroleo; Gas natural; Industria petrolera; Mediciones; Fractura hidráulica |
| Páginas: | 5p. |
| Ingreso de la Info.: | 2013-12-11 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | PETROLEUM AND NATURAL GAS INDUSTRIES -- COMPLETION FLUIDS AND MATERIALS -- PART 2: MEASUREMENT OF PROPERTIES OF PROPPANTS USED IN HYDRAULIC FRACTURING AND GRAVEL-PACKING OPERATIONS |
| Código de Doc.: | ISO 13503-2 |
| Autor Inst.: | International Organization of Standardization. ISO |
| Fecha: | 2006 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | ISO 13503-2:2006 provides standard testing procedures for evaluating proppants used in hydraulic fracturing and gravel-packing operations."Proppants" mentioned henceforth in ISO 13503-2:2006 refer to sand, ceramic media, resin-coated proppants, gravel-packing media and other materials used for hydraulic fracturing and gravel-packing operations.The objective of ISO 13503-2:2006 is to provide a consistent methodology for testing performed on hydraulic fracturing and/or gravel-packing proppants |
| Relac. con otras Normas: | ASTM E11-04, API RP 56:1995, API RP 58:1995, API RP 60:1995, ANSI B74.4 |
| ICS: | 75.100 |
| Idioma: | en |
| Título en otro Idioma: | Industries du pétrole et du gaz naturel. Fluides de complétion et matériaux. Mesurage des propriétés des matériaux de soutènement utilisés dans les opérations de fracturation hydraulique et de remplissage de gravier |
| Edición: | First edition |
| Palabras Clave: | Petroleo; Productos de petroleo; Gas natural; Industria petrolera; Mediciones; Fractura hidráulica |
| Páginas: | 28p. |
| Ingreso de la Info.: | 2013-12-11 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | WELDING OF PIPELINES AND RELATED FACILITIES |
| Código de Doc.: | API 1104:2013 |
| Autor Inst.: | American Petroleum Institute. API |
| Fecha: | 2013 |
| Estado: | |
| País de Origen: | United States |
| Objeto: | API Standard 1104, 21st Edition is the industry standard for welding practices. Welding of Pipelines and Related Facilities presents methods for the production of high-quality welds through the use of qualified welders using approved welding procedures, materials and equipment in a new, clearly understood format. Wide in scope and filled with years of accumulated industry knowledge, the latest edition of 1104 presents inspection methods to ensure the proper analysis of welding quality through the use of qualified technicians and approved methods and equipment. This standard presents methods for the production of high-quality welds through the use of qualified welders using approved welding procedures, materials, and equipment. This standard covers the gas and arc welding of butt, fillet, and socket welds in carbon and low-alloy steel piping used in the compression, pumping, and transmission of crude petroleum, petroleum products, fuel gases, carbon dioxide, nitrogen, and where applicable, covers welding on distribution systems. It applies to both new construction and in-service welding. The welding may be done by a shielded metal arc welding, submerged arc welding, gas tungsten arc welding, gas metal arc welding, flux-cored arc welding, plasma arc welding, oxyacetylene welding, or flash butt-welding process or by a combination of these processes using a manual, semiautomatic, mechanized, or automatic welding technique or a combination of these techniques. The welds may be produced by position or roll welding or by a combination of position and roll welding. This standard also presents inspection methods to ensure the proper analysis of welding quality through the use of qualified technicians and approved methods and equipment. It covers the procedures for radiographic, magnetic particle, liquid penetrant, and ultrasonic testing, as well as the acceptance standards to be applied to production welds tested to destruction or inspected by radiographic, magnetic particle, liquid penetrant, ultrasonic, and visual testing methods. While this standard is comprehensive, it may not address all issues that may arise. |
| Edición: | 21Edition |
| Notas: | Para la consulta de esta norma dirigirse a INTI-Mecánica |
| Palabras Clave: | Soldadura; Tuberías; Aceros; Petroleo; Productos de petróleo; Gases; Inspección; Ensayos |
| Páginas: | 118p. |
| Ingreso de la Info.: | 2013-12-03 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
| Tipo de documento: | NORMA |
| Título: | PETROLEUM AND LIQUID PETROLEUM PRODUCTS -- CALIBRATION OF VERTICAL CYLINDRICAL TANKS -- PART 5: EXTERNAL ELECTRO-OPTICAL DISTANCE-RANGING METHOD |
| Código de Doc.: | ISO 7507-5:2000 |
| Autor Inst.: | International Organization of Standardization. ISO |
| Fecha: | 2000 |
| Estado: | Para datos sobre la vigencia de esta norma haga clic aquí |
| Objeto: | This part of ISO 7507 specifies a method for the calibration of non-insulated vertical cylindrical tanks having diameters greater than 5 m, by means of external measurement using an electro-optical distance-ranging method (EODR), and for the subsequent compilation of tank capacity tables |
| Campo de Aplic.: | This part of ISO 7507 is applicable to tanks with cone-up or cone-down bottoms as well as to tanks with flat bottoms |
| ICS: | 75.180.30 |
| Idioma: | en |
| Título en otro Idioma: | Petrole et produits petroliers liquides. Jaugeage des reservoirs cylindriques verticaux. Methode par mesurage electro-optique externe de la distance |
| Edición: | First edition |
| Palabras Clave: | Petroleo; Productos de petroleo; Tanques; Calibracion; Mediciones ópticas; Mediciones volumétricas; Métodos ópticos |
| Páginas: | 17p. |
| Ingreso de la Info.: | 2013-06-05 |
| Para ver la norma completa busque en la base Normas (solo para personal del INTI) |
[Página de Inicio] [Nueva Búsqueda][Página Anterior]